What Did You Use Your Multitool For Today?
-
Installed one of these Star Treck door panels from thinkgeek.com with my wave. Admit it you want one! Does the whoosh sound when you walk by.

-
@Nhoj said:
Installed one of these Star Treck door panels from thinkgeek.com with my wave. Admit it you want one! Does the whoosh sound when you walk by.The Star Trek door always sounded to me a bit like a shower door that needed some lubrication.
-
Installed one of these Star Treck door panels from thinkgeek.com with my wave. Admit it you want one! Does the whoosh sound when you walk by.
The Star Trek door always sounded to me a bit like a shower door that needed some lubrication.
Just a silly Christmas present I got, maybe I should move it to my shower then! :D
-
Installed one of these Star Treck door panels from thinkgeek.com with my wave. Admit it you want one! Does the whoosh sound when you walk by.
The Star Trek door always sounded to me a bit like a shower door that needed some lubrication.
Just a silly Christmas present I got, maybe I should move it to my shower then! :D
Yeah, where fewer people will see it, preferably <u>inside</u> the shower.
-
Haven't personally had much need for my pocket tools though I did recently rescue two damsels in distress :D I was waiting in line at the post office when a woman asked me if I had a pen. I told her I had a little one and pulled out my 91mm Vic and slid the pen out from the scale and handed it to her. She did an amazingly good job with it writing in the address on an envelope she held curved in her other hand :o She was grateful
The previous day I was entering the service entrance of a hotel I was working at and saw a woman trying to cut a nylon rope by running it up and down the exposed metal edge of a heating duct ::) The scissors on my Style PS made short work of it and she thanked me :) -
I think Lynn did a direct comparison between the modern LM can opener and the Vic can opener.
Oh she did? Perhaps she will shed some light on this subject for me

Sure, here's the thread where it started (and pretty much ends)
</topic/36802
Then it branched into a separate thread to test 15oz cans (with some linked, timed videos)
</topic/37059
And THEN became a discussion on #10 cans here...
</topic/37113The TLDR short version... mostly not a lot of difference, times range from about 22 to 28 seconds on most can openers for 15oz cans. If you use big, #10 cans, either use a Vic (as opposed to a Wenger) or get a locking can opener.
And finally back on topic... I had one of those AWESOME days where you use a multitool to open packages of OTHER multitools! The blade on my Rambler did the work. Go Rambler!
-
@Lynn LeFey said:
I think Lynn did a direct comparison between the modern LM can opener and the Vic can opener.
Oh she did? Perhaps she will shed some light on this subject for me

Sure, here's the thread where it started (and pretty much ends)
</topic/36802
Then it branched into a separate thread to test 15oz cans (with some linked, timed videos)
</topic/37059
And THEN became a discussion on #10 cans here...
</topic/37113The TLDR short version... mostly not a lot of difference, times range from about 22 to 28 seconds on most can openers for 15oz cans. If you use big, #10 cans, either use a Vic (as opposed to a Wenger) or get a locking can opener.
And finally back on topic... I had one of those AWESOME days where you use a multitool to open packages of OTHER multitools! The blade on my Rambler did the work. Go Rambler!
Thanks Lynn
Oh and you gotta love those days

-
@Lynn LeFey said:
I think Lynn did a direct comparison between the modern LM can opener and the Vic can opener.
Oh she did? Perhaps she will shed some light on this subject for me

Sure, here's the thread where it started (and pretty much ends)
http://forum.multitool.or...ex.php/topic,36802.0.html
Then it branched into a separate thread to test 15oz cans (with some linked, timed videos)
http://forum.multitool.or...ex.php/topic,37059.0.html
And THEN became a discussion on #10 cans here...
http://forum.multitool.or...ex.php/topic,37113.0.htmlThe TLDR short version... mostly not a lot of difference, times range from about 22 to 28 seconds on most can openers for 15oz cans. If you use big, #10 cans, either use a Vic (as opposed to a Wenger) or get a locking can opener.
And finally back on topic... I had one of those AWESOME days where you use a multitool to open packages of OTHER multitools! The blade on my Rambler did the work. Go Rambler!
That's why I got my Charge, with the hook-knife early on, to open the packages of the later purchases.
-
Used my Wingman pliers to break up the ice on the bottom step of my bus. Not to technical but it worked.
-
over the last couple days the Spirit X has seen a lot more use. the phillips was used to swap some hard drives, the flathead for installing network cards into a couple ancient laser printers, phillips was used today to open up some barcode scanners and a mini pc looking for serial numbers, and the scissors got put work cutting some barcode labels.
-
Used my Victorinox Cadet Black Alox to
open tools on a husky mt
-
Used my Charge TTi to clean up and repair the leaking roof of the radome on a global communications/satellite tracking station while hanging off the side of a knuckle boom 30m up in the air.
-
I used my PST II to help in assembling a baby bouncer seat and crib. About 6 weeks left :ahhh
-
Used my Charge TTi to clean up and repair the leaking roof of the radome on a global communications/satellite tracking station while hanging off the side of a knuckle boom 30m up in the air.

I was trying not to fall to my early demise, rather than take pics, but i'll hunt up a pic of the radome for you.
-
Used my Surge to install 50 cable ties to hold some lattice work on some winged agility jumps. My dog club had a working bee today to maintain all our agility equipment.
Just to show I'm not a MT "toolist" I also used 15mm and 16mm ring spanners, round file, a hammer and my battery drill. I use the tool that works, whether it is an MT or not (but I did have to drive 30 minutes to get some of the non-MT tools, screws and bolts, whereas the Surge was with me and ready to go right from the start). Score for MTs

-
I'm definitely a toolie since I caught the bug again last fall, and it's usually a skinned knuckle or two that forces me to use a specialized tool instead. It's probably just a phase I'm going through...
-
it's not something you 'grow out off' ! sorry it might get worse and worse ! as you get older you have to give in to your urges :D
-
Used a kobalt 15-in-1 multi tool in the kitchen to open a can of peas.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login