Which Wave should I get?
-
Ok, I've been fighting with myself long enough. I'm going to get myself a new Wave for my birthday. However - which one to get? Stainless or Black Oxide? Do I go with one of the Leatherman sheaths or are there better sheaths out there that you guys like? (I prefer to wear it horizontally on my 1-1/2" Bullhide Leather belt.) I already have a bit kit so if I decide to carry that, the sheath would need to fit the bit kit too, and the bit extender.
What do you guys recommend?
Thanks!
-
@Multiple Personality said:
Ok, I've been fighting with myself long enough. I'm going to get myself a new Wave for my birthday. However - which one to get? Stainless or Black Oxide? Do I go with one of the Leatherman sheaths or are there better sheaths out there that you guys like? (I prefer to wear it horizontally on my 1-1/2" Bullhide Leather belt.) I already have a bit kit so if I decide to carry that, the sheath would need to fit the bit kit too, and the bit extender.What do you guys recommend?
Thanks!
Personally I'd get what I haven't got... B/O with molle sheath
-
SS vs BO is very much a personal choice. I prefer bright SS as it is easier to see and therefore makes the tool easier to locate in amongst other stuff or if you accidentally drop it on the ground and are later looking for it.
Look at Skinth sheaths, way better choices than std LM sheaths.
Site not found · DreamHost
The owner of this domain has not yet uploaded their website.
(www.skinthsolutions.com)
-
I have both in several models. I would go stainless. Save the extra ten bucks and put it toward a bit kit.
-
I myself have wanted a BO version of a multitool, but each time I've gotten a MT, I couldn't spare the cash for the extra cost of BO. SS looks good too though, and I actually may prefer that slightly. However, my opinion could change if I ever get to see a BO MT in person.
-
Thanks - about the black oxide I was actually wondering if anyone has experience in how it wears and if it is an improvement over the stainless. Does the black oxide coating wear off with use? Does the black oxide coating help resist rust? Things like that. I know with my stainless PST (yes it's been that long), it does have some rust and corrosion spots on it and I was wondering if the BO coating actually served a purpose to help prevent that, or if the black just wears off with use then what is the point? If it's just there for looks then I probably wouldn't bother. If it serves a purpose then I might spend the extra bucks.
And thanks, I did not know about Skinth sheaths - I will look them up.
MP
-
@Multiple Personality said:
Thanks - about the black oxide I was actually wondering if anyone has experience in how it wears and if it is an improvement over the stainless. Does the black oxide coating wear off with use? Does the black oxide coating help resist rust? Things like that. I know with my stainless PST (yes it's been that long), it does have some rust and corrosion spots on it and I was wondering if the BO coating actually served a purpose to help prevent that, or if the black just wears off with use then what is the point? If it's just there for looks then I probably wouldn't bother. If it serves a purpose then I might spend the extra bucks.And thanks, I did not know about Skinth sheaths - I will look them up.
MP
Yes, the coating does wear off, will scratch and will show some rust. Some like the worn look though.
-
You're going to get a lot of different opinions here I'm sure, so here's mine:
Personally, I prefer the natural stainless finish. The black oxide is cool but I've heard that oil can dissolve it and blacken your hands.
I used to carry a Wave, but upgraded to a Charge TTi.
Sent from my HTC Desire HD A9191 using Tapatalk 2
-
I'm surprised that no one has given you the typical MTO response... Buy both :D
Things to think about would be, will you ever use it to cut any sort of food? Personally I'd rather not use a BO tool to do that. As Landrew said, you do have a good chance of getting some of the coating on your hands when using it (especially in the beginning), and it can/will scratch and wear off some as the tool is used.
I prefer the bare look myself, but if I came across a BO Swiss Tool that was a good price, I might have to pick it up.
-
Mines been hard used for a while now. Used it for field work on exercise, fishing, little DIY jobs etc. Mine was pretty scuffed up before I took it fishing but cleaning it in a concoction of bleach and soap to get the smell out of all the little gaps didn't do the BO finish any favours haha

-
BO is a little harder to find if you set it down somewhere, especially outdoors in an unfamiliar environment.
More importantly to consider ... It's harder to find if SOMEONE ELSE sets it down in such a manner.
"Hey do you have my Wave?"
"No, I put it down just over there?"
"Over where?"
"Umm..."
:)
-
There is an orange handled Wave too. Poll time!
-
I like the black oxide version. The bead blasted Leatherman tools tend to be rust magnets for me. I'll take all the help I can get!!!
--
sent via carrier pigeon from my secret hideout -
Awesome, thanks guys. The food comment kind of made up my mind. I think I will go with Stainless. Dude, where did you get the orange handles?
-
I think Cabelas was selling the orange handled MT
-
Years ago, I used to make a few tools; nothing serious, a few punches and chisels. I made the black finish with a smoky acetylene flame and seared it into the surface with heat before tempering. Not sure how leatherman does it, but my way probably made a fairly toxic surface, which I certainly wouldn't want to contact food.
-
-
I've purchased over 20 multi tools in less than a month -none of them black.
Don't give me ideas!Sent from my HTC Desire HD A9191 using Tapatalk 2
-
I most of the time buying ss and bo at the same time, but I just love the way a bo looks after some use. So my edc is a bo
-
First and only black oxide I have is the Surge. It was actually listed cheaper than the stainless.
BO scratches easier than I had expected, and starts looking rather ugly. Having to file the squared edges also gave a pinstripe appearance.
Have seen an issue with laser engraving too. My first I had done oiled and rubbed off the excess coating and used for a week before it was laser engraved. Came out sexy! (Top)

Then after a long dramatic event in proving the safety pin issue it was replaced. I don't even think Leatherman wiped the excess off, and surely did not treat it with oil then wiped it either. (Bottom)In the end wished I would have kept the original and sent the replacement back, despite off of the scratches.

Nothing beats your first!
Sent via Sonic SAK Screwdriver
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
