Super DIY SAK Liner Cutter
-
Thanks! I dread making liners by hand, so this way I can at least make up a bunch and go back to the modding parts I enjoy. Plus I used up all my stock nickel silver liners so I had to figure something out. :D
-
Well I did end up making a bunch of brass liners which I'm now getting around to using. They still need finishing, but my templating jig worked just fine for roughing out the shape.

The next templating task I set my mind on was making a scissor rest piece in the shape of the keyring liner part. This just happens to make a pretty decent scissor rest and has the nice benefit of making a much stronger keyring attachment. I just used 4 of the liner size 0.040" parts as the guide and it worked just fine.


This is 12 gauge 304 stainless which just so happens to be exaclty 0.105" the same thickness as the back spring.

And here you can see how it fits with a backspring just as the original liner keyring part does.

-
Ok Ive been meaning to update this post for awhile now. I need to make a bunch more Al liners to get hard anodized so I thought Id take pictures of each stage as I go to show what I do.
So stage one is that I covered 1 sq ft of 6061 T6 Aluminum with label paper. Note that I usually just print out these templates and stick them on, but my printer is out of ink, so I just traced these on, for the same effect, but slower. I can get 54 pieces from this size.

Next I use a punch and mark one start point for drilling in each piece, just one and I always mark the same side for speed later on.

Next I rough cut them all with a jewelers saw... I'll photo that and add it, and the rest as I go.
-
It's nice to see the process.... wish I had your patience! :D
-
+1 Looking forward to the updates.

-
Ok I need to make up some more liners to get anodized red for the super popular black scale red liner look, so on to the next stage.
Basically at this point it's just a LOT of hand cutting with the jewelers saw. It's slow boring and hand cramping work, but its the best way I have to do this at the moment. Luckly I am just rough cutting these out as I cut the precise shape at a later step, its basically just cut them apart as fast as I can.




Oh and what's more exciting than watching competative darts on tv? Watching someone sawing! Thats right, watch me cut out all 54 by hand! Kidding, just 3... :D
Oh also skip the jokes about the sawing motion, Ive heard it all before from my wife making comments while watching me cut parts. :D
-
Dubious sawing action? I'm sure I don't know what you mean.


-
-
Very informative thread, thanks for sharing! :)
-
You look like you've had a lot of practice at that mate

-
All I can say is bahahahahaha hahahhahahaha and
lol -
Ok guys, back to liner making. We left off last time with me hand cutting out a bunch of pieces, and each one had one punch mark on one side of each piece.
So after alot more cutting I ended up with 54 Al parts, and 24 brass.

Now for the drilling.. I mean lots of drilling, no really hours of drilling. (54 + 24) * 3 = 234 holes.
Ok, so each rough cut liner has the right side hole punched like so...

So I drill those out...

I end up with 78 parts with one hole drilled.

-
Here is the gear I use to drill the remaining 2 holes per liner.

Two broken carbide drill bits with tape for handles are my pins, and the drilling guide I made from simple 316 stainless, with very carefully located and drilled guide holes.
So to start, one guide pin goes through the guide and the single hole in the liner.


I visually line up the hole on the other end with the mark on the label paper underneath, and clamp the parts together with vice grips.

Now back to the drill press and the other end hole gets drilled.

And now I have both end holes drilled.

-
A second guide pin goes in the new hole and the vice grips are removed.

Next, you guessed it. The center hole is drilled.


And there we have it. One liner drilled with all three holes accurately located.

Now I just had to repeat this 77 more times to yield my 78 rough cut, but drilled liners.

That killed my wrists, so I will show the next steps tomorrow, which are fit up on the router pins, and routing to the exact profile.
I needed to make a bunch of Al liners up to go for red hard anodize, since I'm all out and people keep asking for black scales and red liners. :D
-
Thanks for documenting all this! It is fun to watch your progress and see all your skill and patience along the way.
Sent from my MB886 using Tapatalk 2
-
Thanks for the updates.
BTW did you get the mill you were talking in the birthday thread yet? Wouldn't it speed up the whole liner cutting process or would too much material go to waste? -
No mill yet. CNCing would be nice to cut the profiles for sure. I had the money saved up but I still didnt pull the trigger all they way yet...:D I think I still would cut up the pieces first for blanks then have the CNC go round a stack at a time to profile so that I dont waste as much material. But the easiest would be to have the CNC mill out the shapes from sheet stock with a 1/8 straight bit and leave some tabs. It would waste more material since Im making a 1/8 cut, but the speed might make that not matter so much.
-
No doubt, that is a LOT of holes to drill. :-\ Cheers for sharing mate.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
