The Splash - LM Squirt Mod
-
Hi Eric
The finished tool looks awesome -
Hi Eric,
This is one of the best projects in a long time. It looks like a Squirt Pro!!!
You may have to take orders on this one ;)
Cheers,
Pete
-
I'm thinking this one could be one of the most expensive mods you've done. :D
How many Squirts were sacrificed to get all the tools you needed for this mod?
-
-
I'm thinking this one could be one of the most expensive mods you've done. :D
How many Squirts were sacrificed to get all the tools you needed for this mod?
That's a good point... it was toolicide :ahhh
I rally love it though. I would carry that in my pocket no problem

Just wait till you see the new scales. They maybe thicker, but they sure are going to be Purdy!
@enki_ck said:
I'm thinking this one could be one of the most expensive mods you've done. :DHow many Squirts were sacrificed to get all the tools you needed for this mod?
You know, not that many. Only one of each, a E4, P4, S4 and a PS4, all I got cheap off eBay. The whole project not counting the custom scales is still coming under $85.
-
Let's take a minute to honor those micro MTs that were sacrificed for the Greater cause known as the Splash.
The mighty P4, a micro tool beyond its years.
The irreverent E4, heroically making connections and bridging circuit gaps.
The legendary S4, successor to the Micra throne.
And finally the youngest, the PS4, who tried to do everything at once with such vigor.


Open bar for the gentlemen and open casket for the ladies (Stinson quote).

--
Here's a colour photo for the rags.

-
Washers to washers, rust to rust...

-
Brilliant pocket MT
It's just my opinion but isn't it time that you design your own MT from scratch and show the industry how it should be done, the thought and effort that you put into your designs show that the MT community is missing out, i'm not kissing a** but i would buy one of your MT's, i'm not knocking leatherman (i have a few of their tools) or any of the other manufacturers, but it's got to the point that they dictate what we buy, with very little choice, you've shown by listening to other members that you can build what is wanted within the community, keep up the good work. -
@barryj323 said:
Brilliant pocket MT
It's just my opinion but isn't it time that you design your own MT from scratch and show the industry how it should be done, the thought and effort that you put into your designs show that the MT community is missing out, i'm not kissing a** but i would buy one of your MT's, i'm not knocking leatherman (i have a few of their tools) or any of the other manufacturers, but it's got to the point that they dictate what we buy, with very little choice, you've shown by listening to other members that you can build what is wanted within the community, keep up the good work.Yah, the amount of R&D that goes into a new brand new tool without directly lifting ideas, patents and techniques is very high.
My work is primarily a hobby and to let my brain stretch in different areas. I love working with my hands, make details that would otherwise be overlooked and see where things could be improved.
Thank you for your vote of confidence!
-
...behold! COMBO TOOL!
Before I put and edge on it and final polish. It's a small warney/picker/xacto style chisel blade. Cutting surface only about .75" long.

Some file work to indicate it's use. Three small jimps and a point for a blade. Better pic later.

Three different sizes of wire strippers, don't know what actual gauge but you get the idea.

Here it is installed and with and edge and polish. Used my Lansky with diamond hones and a ultra fine stone for the final run at 30 degrees.


And some pics of the file work on the spine. I have the nail file file work a bit of a polish too. The serpentine pattern is a lot more visible.

And the otherside. Notice the serrated blade file work (nothing too exciting, just a row of indents)

Edit: here's some better pics in better light.


Mmm shiny!


I took a couple of assembly photos but I'll make that a separate post so it's easier to see.
-
Here are some assembly pics and tricks if you ever decide to assemble a Squirt.
Have all your assemblies near by, thread the outside tools into place and get the plier head/spring cam ready.

Now, pay attention to which way the back spring frame goes. The back spring rest should be farther away from the plier pivot.
Here's the biggest tip, align and thread the PLIER and CAM FIRST before you install the back springs. With any tension from the springs, it's much easier.

Now slide the back springs into place, you will need to back off the pin so you can slide both springs in at once. One they are lined up, use a pair of pliers to squeeze the back spring up towards the spine, while at the same time tap the whole assembly so that the pin can slide into the hook of the spring. One at a time or both.
Best to have a block of wood or something hard and non marring to tap the pin in while holding the pliers.
All the way through

Continue sandwiching the parts. If you are building a standard squirt, this should be your outside layer.

That's pretty much it!
-
Yoooowsa!
Just counted the "functions" and it came out to 21and if the new scales work, it'll be 22.
Let's see, I'll list them out
- Awl
- 2D Philips
- 3D Phillips
- Flat driver
- Bottle opener
- PE blade
- SE blade
- Scissors
- Med gauge wire stripper
- Small gauge wire stripper
- Micro gauge wire stripper
- Warney/Xacto blade
- Nail file
- Cuticle pusher/nail gunk remover
- Eye glass driver
- Tweezers
- Bolt pliers
- Needle nose pliers
- Soft wire cutters
- Metric ruler
- Imperial ruler
Potential
- Hex bit driver (scales TBA)
--
Time for a new splay photo.

-
Both ridiculous and awesome!

-
That thing is looking great Eric
I was still kind of hoping for the ruler scales but oh well. -
@stealth007s said:
That thing is looking great Eric
I was still kind of hoping for the ruler scales but oh well.I'll save it for another mod, when the length is more useful :D
-
I am saving this pair of pliers for when the scales come in. I'll need to tear the whole thing down anyways. Pocket jewel!
A little bit of a different pattern of serpentine that will also double as a thumb grip (I noticed I put my thumb on the plier head when I was torquing down on something, sorta like Vic pliers)



Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



