CyberTool bitdriver metal
-
Here it is. In daylight the difference is easily distinguishable. I might post another one tomorrow.

-
Thanks mate. Pretty big difference between the tools there, but as long as it works I suppose.. :)
-
I suppose the bit driver is rather drop forged than cast, or at least i hope so. ;)
The metal is of different colour than teh SS tools because a different kind of steel is used, It´s a more elastic and tough steel that is not as brittle as the blade/tool steel.
Most likely the steel is less rust resistant than the other steel used in the knife and so is eitehr chrome or nickel plated to achieve a hard, corrosion resistant finish (like you would find on wrenches).
So most likely the quality is not "worse" but just different to achieve certain abilities. -
Here's a daylight photo

-
Polish it with Flitz and it will look like new in seconds.
-
That's a nice photo, thanks.

Yeah, I suppose it's not so bad, I might end up polishing it now and then just to make sure it won't start picking up rust. Doesn't seem overly common with them rusting though.
-
It doesn't look like rust. It seems that a coating is destroyed by rubbing with the hands (and sweat rich in fatty acids).
I don't know that Flitz product. I might try with something available here. What is it for?
We have a few polishing agents with easy names, Silvo for silver, Brasso for Brass, etc. what metal should I search for? -
Looks more like a very light oxide of some sort, but not rust. Mine is similar, but I always assume the metal was a little different to the main tools.
-
Ya its not rust. I polished mine the same way I do all steels and it took ok. Fine sandpaper and then a dremel with wool buff.
The rust I found on a used one was on the inside of the hex hole.
-
Not knowing a lot about metallurgy, my uneducated guess is it's probably got a higher carbon content in it to make it springier and therefore tougher than the stainless used in the other tools.
As for the magnetization thing, I haven't tried this myself, but there are small and high powered rare-earth magnets made as spacers for flat top li-ion cells used to act as positive terminals for those cells. I'd think a small one (link included below) might fit inside the bit driver to help hold bits in place.
I'll try and see if one will actually fit, and if I can figure out a way to easily get it back out, I'll experiment with it to see if it will actually work.
-
I have a Cybertool, from back when they were first sold in the US. It's been used steadily since I first got it. It lives on my desk at work. My driver shows no discoloration whatsoever. ???

-
They might have changed the material at some point.
-
@Buzzbait said:
I have a Cybertool, from back when they were first sold in the US. It's been used steadily since I first got it. It lives on my desk at work. My driver shows no discoloration whatsoever. ???
Maybe they switched to something cheaper to shave some bucks off of them?
There's just one solution..

-
I bet you're right. That CT has the older thicker main blade too. Unless they all do, but I figured recent CT have the thin one?
-
I can hardly even tell that my driver is cast. I never actually noticed until this thread got me looking.
-
The Cybertool34 is the SAK I've owned the longest, and is easily the most used multitool in my collection. My mother bought it for me when I got my first government IT job. It's the one multitool that I never really think about. I just take it for for granted that it will be there every day for me to use. In fact, it's become a fixture in my office, that everybody knows they come over and borrow when doing repairs.
If I were suddenly inflicted with a bout of honesty, I'd admit that the Cybertool could probably handle most all of my everyday impromptu multitool needs.
-
I wonder if these older drivers were plated on top of the casting, and Victorinox eventually dropped the plating.
-
I have over 30 cybertools. All look exactly the same after being polished with Flitz. I had one I got used and it looked like it was left in the road for while and got run over a few times. The top of the driver was all chewed up. I filed, sanded and polished it and it looks like new. There is no plating. It is solid stainless all the way through.
-
@GigaHz said:
I have over 30 cybertools. All look exactly the same after being polished with Flitz. I had one I got used and it looked like it was left in the road for while and got run over a few times. The top of the driver was all chewed up. I filed, sanded and polished it and it looks like new. There is no plating. It is solid stainless all the way through.That's pretty reassuring, thanks mate. :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login