Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

93mm with scissors

Scheduled Pinned Locked Moved The Mod Squad
11 Posts 1 Posters 2.1k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. 93mm with scissors
93mm with scissors
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • pawn Offline
    pawn
    Posts: 54
    pawn Offline
    pawn
    wrote on last edited by
    Quote Reply

      Hello everyone!

      This weekend, I tried to put some scissors into a farmer and exchange the woodsaw for a metal file.
      I used a solo spring for the scissors and the saw spring for the metal file (obviously).

      The saw worked perfectly, but the scissors are a bit flobby and don't close nicely.

      Do you guys do anything else than grinding a bit on the spring to make room for the scissor handles?

      All parts were new, except the scales, which were very used old red ones. Fortunately the scales were used because DAMN PEENING ALOX SUCKS!!!!

      I used a very small hammer and was super carefull but about 20% of the blows land on the scales, if you don't want any horizontal play in the blade left.
      How do you do it? Any tips?

      • pawn
      1 Reply Last reply
      • PTRSAK Offline
        PTRSAK
        Posts: 4,776
        PTRSAK Offline
        PTRSAK
        wrote on last edited by
        #1 Quote Reply

          I'm in exactly the same situation with my Alox Explorer. I'm happy with everything except the closing of the scissors. The Solo spring needs a "ramp" ground on the inside where the end of the "free" scissor handle hits so it doesn't jam with the scissors slightly open and "deployed".
          Also I think the Solo spring needs a bit more set on it to provide more tension to snap the scissors into the stowed position more firmly.
          I will be breaking mine down again and giving the spring a bit of a tap with a hammer to bend it slightly for more tension.

          I use a piece of leather with a hole in it to protect the scales when peening Alox. and I am also playing around with making a punch with a dished head to "finish" the riveting of the pins.

          I did see a post where someone was using the reinforcement rings for punched notepaper. Six of them appeared to do a good job.

          Merit Badges
          Hacker MTO Tool Scale Changer Birth Year SAK ALOX Colors Level 3 Flashlight Fire Making Ignore
          1 Reply Last reply
          • Syph007 Offline
            Syph007
            Global Moderators
            Posts: 9,842
            Syph007 Offline
            Syph007
            Global Moderators
            wrote on last edited by
            #2 Quote Reply

              There are actually 8 different variations of scissors over the years. The older ones with the fatter thumb rest work way better with solo springs than the modern thin style. Ive seen them with both riveted and screw pivot type, so I dont know when they changed. When I was using solo springs for scissors the fatter handle type was the way to go and I only needed to grind a bit of spring and they closed just fine.

              1 Reply Last reply
              • pawn Offline
                pawn
                Posts: 54
                pawn Offline
                pawn
                wrote on last edited by
                #3 Quote Reply

                  Aw, man! I have to look at home, if I have such a scissor.
                  Else I will just bend the spring a bit more, and hope it doesn't destroy anything.

                  @PTRSAK: My concern is not really with the shape of the end of the pins, but more with getting it tight enough. If I want a good fit, I have to hit the pins until they are under the level of the scale...

                  1 Reply Last reply
                  • jrp316 Offline
                    jrp316
                    Posts: 436
                    jrp316 Offline
                    jrp316
                    wrote on last edited by
                    #4 Quote Reply

                      Easiest way I've found to do it: get Syph to take care of it >:D

                      You'll get it, no worries...just keep grinding away at it (figuratively and literally).

                      1 Reply Last reply
                      • crackout Offline
                        crackout
                        Posts: 864
                        crackout Offline
                        crackout
                        wrote on last edited by
                        #5 Quote Reply

                          My experience with scissors on 93mm knives are similiar.
                          If you use Solo springs you can't rest the scissors on the spring. The scissors' handle is the thing that defines the position of the locked tool. When grinding the solo spring to create a ramp where the handle slides along you have to be careful not to remove too much material or the tool will sit too deep inside the construction.

                          What I found is that the sweetspot for the ideal position does not a allow a full snap from around 50°. It stops due to the rest of the material that's kept on the spring to allow for a nice positioning. However, between 0° and 30° I get a full snap. Syph is right about the kinds of scissors, the older ones work better. I think the only 100% solution are his custom springs.

                          1 Reply Last reply
                          • Syph007 Offline
                            Syph007
                            Global Moderators
                            Posts: 9,842
                            Syph007 Offline
                            Syph007
                            Global Moderators
                            wrote on last edited by
                            #6 Quote Reply

                              @crackout said:
                              My experience with scissors on 93mm knives are similiar.
                              If you use Solo springs you can't rest the scissors on the spring. The scissors' handle is the thing that defines the position of the locked tool. When grinding the solo spring to create a ramp where the handle slides along you have to be careful not to remove too much material or the tool will sit too deep inside the construction.

                              What I found is that the sweetspot for the ideal position does not a allow a full snap from around 50°. It stops due to the rest of the material that's kept on the spring to allow for a nice positioning. However, between 0° and 30° I get a full snap. Syph is right about the kinds of scissors, the older ones work better. I think the only 100% solution are his custom springs.

                              Exactly correct. :D The handle determines the rest position and the snap is all done by the pivot on spring action. You don't need a ramp, unless you can graft some metal onto the spring, which of course is an option, but more work.

                              This is why the fatter handles worked better as they hold the scissors at a better stop position. Last time I bought 20 scissors from tom all rivet type, half had fat handles half skinny, so its still possible to have the modern rivet type with a fat handle.

                              1 Reply Last reply
                              • crackout Offline
                                crackout
                                Posts: 864
                                crackout Offline
                                crackout
                                wrote on last edited by
                                #7 Quote Reply

                                  I have a pair of riveted scissors with the fat handle. Those have a steel rivet.
                                  Maybe that's the disinguishing point with the modern ones having silver nickel/brass rivets?

                                  1 Reply Last reply
                                  • Syph007 Offline
                                    Syph007
                                    Global Moderators
                                    Posts: 9,842
                                    Syph007 Offline
                                    Syph007
                                    Global Moderators
                                    wrote on last edited by
                                    #8 Quote Reply

                                      @crackout said:
                                      I have a pair of riveted scissors with the fat handle. Those have a steel rivet.
                                      Maybe that's the disinguishing point with the modern ones having silver nickel/brass rivets?

                                      I have some modern skinny ones with steel rivet too. So they are all over the place. :D

                                      1 Reply Last reply
                                      • crackout Offline
                                        crackout
                                        Posts: 864
                                        crackout Offline
                                        crackout
                                        wrote on last edited by
                                        #9 Quote Reply

                                          Dammit. :D

                                          1 Reply Last reply
                                          • PTRSAK Offline
                                            PTRSAK
                                            Posts: 4,776
                                            PTRSAK Offline
                                            PTRSAK
                                            wrote on last edited by
                                            #10 Quote Reply

                                              @crackout said:
                                              Dammit. :D

                                              When was the last time you saw ANY SAK feature with a simple and consistent change-over in type or date? :poh:

                                              Merit Badges
                                              Hacker MTO Tool Scale Changer Birth Year SAK ALOX Colors Level 3 Flashlight Fire Making Ignore
                                              1 Reply Last reply

                                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                              With your input, this post could be even better 💗

                                              Register Login

                                              1. Home
                                              2. Tool Talk
                                              3. The Mod Squad
                                              4. 93mm with scissors
                                              Reply
                                              • Reply as topic
                                              Log in to reply
                                              COMMUNITY LINKS
                                              EDC-TV SAKWiki GearFeed SAKSelector
                                              Operational Funds

                                              Help us keep the Unworkable working!

                                              Make A Donation
                                              November Goal: $300.00
                                              Due Date: Nov 30
                                              Total Receipts: $0.00
                                              Below Goal: $300.00
                                              0% funded
                                              • Login

                                              • Don't have an account? Register

                                              • Login or register to search.
                                              • First post
                                                Last post
                                              0