Help with Leatherman TTi
-
Welcome the forum man.
My Charge AL and ALX were very stiff to open when I first got them. I used the movie/TV break in method. Watch a movie or TV and and open and close the pliers over and over again. It will break in faster and loosen it up alittle.I have been doing the above and on the serrated knife handle, it became more stiff with like a 'grating' movement. Looking at the pivot joint, there's alot of metal bits that must of come from it. The other pivot don't have this. This normal?
Uh.....no. Blow those shavings out of there, or use a toothbrush to clean them out. Then put a drop of sewing machine oil on that area (not WD40)
Then work the pivots some more and check if it is still shaving metal.
-
@J-sews said:
Uh.....no. Blow those shavings out of there, or use a toothbrush to clean them out. Then put a drop of sewing machine oil on that area (not WD40)Then work the pivots some more and check if it is still shaving metal.
Lol, did as you suggested, but more shavings were still been made. So obviously 2 surfaces are not wearing smoothly. Checked closely and suspected it was these 2 areas. The gooves in the green area were quite deep.

So I got out the old Dremel and tried my best to take out the grooves and a bit more. Was bit difficult as the area was small. Gave it a good clean and the action is now like it should be! :)
Here's the culprit with the jagged edge.
Hmm......maybe this TTi slipped passed LM's quality control??
-
It's really a factory defect.
-
Your really not having much luck are you mate :(, but good job on the clean up though :), should work like a dream now.
If you want to compare it to another Charge, I'll be bringing mine to the big UK meet in July...
/topic/3140
-
I just checked my TTi. Weqr, here are two pictures of my TTi taken at slightly different angles.
Eddie


-
It should be tight when you first get it,but it will loosen up over time,a lot of the marks are tool marks from machining, If my tools don't have scraps and scars on them,I probably don't need them.
-
Mine look like Eddies; untouched mostly but with a little shine at the point where it's almost fully open.
Nice job on the polishing weqr. Too bad you can't bevel that rough edge on the handle slightly. :-\
-
Thanks for your replies guys. Now the other pivot is wearing too! Once I have sorted it out I hope theres nothing more!
-
That just doesn't seem right. :-\
-
Are both sides (the parts rubbing each other) wearing equally?
-
Well, I finally done the other side too along with polishing the other parts you can see. :)
Should be hassle free from now on. ???edap617, not sure what you mean?

-
There's too much wear and tear in the middle section of the TTi in your photo.
Eddie
-
I have two Charges, one the natural titanium color and the other all black.
I carry the natural one every day and use it at work considerably.
It will get a bit rough looking from every day use. That is what I bought it for.The black one is for those days when I dress in all black, and want my accessories to match.
Thus a black Charge, Black knife, black Flashlight, etc.The black one is seldom used and still remains looking like new.
-
But will they match with your high heels?
I can't imagine the expense I would have to go into if I were to match things like my wife does.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login