Hints and Tips thread.
-
Two different designs.
-
@kkokkolis said:
One can adapt a 6mm Hex bit adaptor for use with the Philips screwdriver. It works for both the old (blue) and new (red) types of drivers. You just fill the tube with some elastic material, rubber or foam, and then stick the driver inside. Now you can use any 6mm bit.
I'm still researching for a way to use X-Akto blades, preferably with a thin SAK (Cadet, Spartan, Climber etc).wonder if the leatherman adapter would work. Have you had any problem with the foam or other material breaking up ? great idea

-
No, not yet. I took the foam from a cheap plastic pen. The rest of the foam is used as a container for 3 cybertool's bits. I have a slight play and I'll keep my eyes open for a more dense material but it works as it is. In fact the XLT doesn't need this adaptor (I have 7 double bits already) but it would be highly functional for a Swisschamp or a smaller SAK with inline Philips.
I wonder too about that Leatherman adaptor. A full Bitset costs 35€ here and it would be easy to buy it if I could justify using it somehow with a SAK. -
@kkokkolis said:
No, not yet. I took the foam from a cheap plastic pen. The rest of the foam is used as a container for 3 cybertool's bits. I have a slight play and I'll keep my eyes open for a more dense material but it works as it is. In fact the XLT doesn't need this adaptor (I have 7 double bits already) but it would be highly functional for a Swisschamp or a smaller SAK with inline Philips.
I wonder too about that Leatherman adaptor. A full Bitset costs 35€ here and it would be easy to buy it if I could justify using it somehow with a SAK.I will try it when I get home and let you know.
-
Thanks.
-
@kkokkolis said:
Thanks.Well no go on the bit adapter, or any of the Gerbers.
-
The fish scaler makes a great pumpkin carver for the little ones during Halloween.

-
I haven't played with a fish scaler yet but I'm sure it has some uses built in it.

So does the multi-purpose hook : you can extend it to facilitate your grip on the SAK when using saws, scissors or even screwdrivers. It's barely noticeable but I find it very practical during prolonged use. Works with both hands as well. Voila.
Cheers
-
Not sure if was mentioned yet, the flathead/bottle popper & the Phillips lock-in temporarily when used on the Wenger S557. These tools press into the springs when bearing down on a screw. This safety feature keeps the tools from folding over during use, then pop back out to normal when the force is removed.
Quite a unique feature.

Lubricating these scales is most interesting due to the tight fitting. Initially applied force, then applied some oil in the tiny spring opening. Just worked that tool on a vertical object to get the lubricant inside.
-
Fishscaler on a Waiter makes a tasty picknick SAK

-
@firiki said:
I haven't played with a fish scaler yet but I'm sure it has some uses built in it.
So does the multi-purpose hook : you can extend it to facilitate your grip on the SAK when using saws, scissors or even screwdrivers. It's barely noticeable but I find it very practical during prolonged use. Works with both hands as well. Voila.
Cheers
it's magnetized
-
so it's not a factory setting?
-
The Fish Scaler tool is a multi-purpose fishing tool only available on some 91mm knife models. The ridged bottom edge of the tool is the fish scale remover. The tip is a "U"-shaped fish hook disgorger used to safely remove a hook from a fish's mouth. The tip is magnetized on some versions, empirical evidence suggests those models manufactured prior to 1985.
sakwiki
-
I magnetized mine easily and allready fished some screws from tight places. It helps also to keep a needle (two for me) under the fish scaler/ wood saw space. Even when carelessly unfolding the scaler the needle is held in place magnetically (and comes out with the scaler, ready to use). Do it. There is no drawback.
-
@Xelkos said:
Not sure if was mentioned yet, the flathead/bottle popper & the Phillips lock-in temporarily when used on the Wenger S557. These tools press into the springs when bearing down on a screw.Vics function in a similar way: The key-ring is part of the bottle opener's spring that you can push down with your thumb to increase friction. The half-stop notch further helps with that. Finally, when, with the bottle opener open, the can opener is deployed tension is somehow increased thus resulting in a almost locking flat driver. Surprisingly, the can opener's stiffness is not affected. You can try this by opening the can opener first and then see how the bottle opener's action becomes harder.
-
I use the Leatherman removable bit driver with the small screwdriver on the back of the Craftsman. (Its on the Handyman and Champ too, and probably other models) I keep a small piece of gutted paracord inside the driver. It locks it on to the screwdriver pretty well. It also scrunches down inside of the driver when I use it with my Juice S2 so there is no need to take it out. The "T-handle" isn't ideal but works for some applications.


-
That's a rather clever find, thanks for that

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

