Tapered Layer
-
Last night I was contemplating all the reasons why this old knife felt so good in the hand. There seems to be many reasons tied to the great craftsmanship that was used in its making. One particular point I wanted to share was when I noticed the taper was lateral as well as longitudinal. This is an old VICTORIA horticultural knife.
Sorry for the bad pic, but I think you can see how the spring, and thus the layer, tapers from left to right. I added the two parallel red lines so one could get a better idea.
Has anyone noticed this before on any of their old knives?

-
I noticed it before, I think it was on this one:

May be similar to your old one.
-
That knife is similar, has the same VICTORIA tang stamp. Mine has the modified clip-point blade, and a polished stainless bud blade. What's the length of your knife?
-
I have a similar knife. However it has no taper, possibly because it has two full blades (clip and wharncliffe). Length is 3 1/2" closed.
-
Yes I've noticed a tapered back spring on one or two of my oldest Officers.
-
I have a couple of older 84mm knives with a noticable taper. It looks like only the blade/corkscrew layer is tapered. The bottom end is about the thickness of one liner thicker.
That Victoria knife I posted earlier has no taper by the way.
-
With a tapered backspring and palm swell must be great to hold in hand.

-
@J Mackrel Jones said:
Yes I've noticed a tapered back spring on one or two of my oldest Officers.Interesting; so those would be 2 layer models?
@Reinier said:
...
That Victoria knife I posted earlier has no taper by the way.Oh OK, thought it was a tapered one as well. Interesting as it look to be of similar vintage.
-
Photo showing tapered back spring - Not Officers but Worker's knives; the first one is the most apparent:
Victorinox from Riethmuller Zurich, wood handles
Victoria with bone scales and slim marlin spike
Fiber-handled Victorinox etched Elsener Zug
When do you figure these were made?

-
And a couple Officer models:
Dolmetsch - Riethmuller shop made by Elsener, fiber scales
Wenger Delemont three faces stamp, horn scales
Both the carbon steel of pre-1920s; nice brass dividers and liners. "Bird's-eye" rivets on the Wenger.The middle spring of the Elsener, backing large blade and wood saw, tapers one direction, and the spring under the corkscrew, backing small blade and scissors, tapers the other direction.


-
Very interesting knives, especially the one with the separate asymetrical tapers on the two layers.
I wonder if this was done more to fit the two tools in the same layer easier, requiring less precision, rather than ergonomics, or maybe a bit ot both? Maybe some knife makers would know the history of this approach. ... Maybe once they were able to get the grind right and give the blade a bend/twist they didn't need to do this anymore? I certainly would make building more layers easier not to have the taper.
This knife is also interesting because I've seen a couple Wenger with the wide spring for two tools, but I don't remember seeing it on an Elsener/Vic knife yet; but I may be forgetting this detail. These seem to be an early design for including the SAW in the Officer style knives.
Do we know when Victorinox or Wenger moved to stamped blades? This might be another oimportant aspect for them choosing the steel formula they did, as it would have made stamping much easier.
I don't know when those Worker knives would have been made, I'll mention that even though Stainless-steel started being used in the early 1920s, like transitions today not all knives would have switched to using stainless steel at the same time, and I expect some of the worker knives switched later than the Officer knives. I think they could have been made as early as 1910 and as late as the 40s, I seem to remember very similar models all the way into the 40s catalog images, and I don't know if they have completely switch to stainless by then as you can't really tell from the images. I think the n/s bolsters are a good clue on the age, but I don't know when they started using those.
The tapered knife I showed has a carbon blade and spring, but a nicely polished stainless steel budding blade, so there was definetly a period of overlap; even within a single knife. Interesting but at some point that small budding/grafting blade transitioned to brass and never changed from that to the present day. I'll take more pictures of that knife next time I have some good light.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login