Wood Scaled SAK pictures thread.
-
This piece of Brown Mallee burl has some pretty heavy cracking and tended to fall to bits when cut small enough for SAK scales. So I tried a pair with gluing the wood together down the middle to help it hold together.
Now I can't decide if it looks good or looks like offcuts glued together




-
Looks almost leaf-like. Especially in photo #3. Too bad there wasn't a wood that veined out and looked more like a leaf without breaking up.
Your knife does look okay, least photos from the photographic viewpoint. Though the near straight lines ... Is that how it split, or did you take the wood down and glue them together?Does look interesting though.
Dad used to cut and polish rocks. Wonder if anyone tried to make scales from rocks? Maybe the bug is loose and someone with lapidary equipment could start a new topic. 
-
the worst cracks are on the corkscrew side, you can see three of them in photo 4. those go right through and have been glued together. I cut 2 pieces of wood in half lengthways and glued a cracked and non cracked half together for each side, that centre glueline is the cut. You can see the other cracking along the piece next to the openers.
Actually it's growing on me... plenty of character.
I have been looking around trying to figure out how to do some stone scales for a recruit. Looking at granite or marble floor tiles but they are too thick, maybe marble wall tiles.
-
Speaking of wood... for some reason I bought these today
Highly figured Olive wood pen blanks A1++ grade (second's)
They are big enough to get 2 knives worth of scales (4) from each blank.
or possibly 5 sets of 58mm scales each.Including postage it was $40 for the lot because they are seconds. Still should be able to get a bunch of scales out of them.
Should keep me busy for a while.
-
Was thinking once about taking a wood scale and put a round dip in it from the liner side, with a small hole protruding out the scale side. Then glue a small cabo stone on the inside. The scale would be the frame for a polished stone. Dad had a bunch of stones here, some opals, but could not find them. Think a cousin ran off with them during the move, so the idea got hosed.
The stone would act as an inlay so to speak, or logo. One could probably incorporate something like that with attractive hard woods and make a name for themselves. Australia has a lot of opal mines don't they?
Could not find any decent lapidary rock slabs online, but you'd need a decent setup to cut and polish them. But I do see others thought of the stones scales too.
-
-
-
-
-
-
@lowtech said:
Just a run of the Mill one, but not seen too often:EKA / Wenger:

Loadout:

Compared to a standard Wenger:

Nice one Thomas
I've just made yet another attempt at buying a Wood 03 from an overseas store .... I'm determined to find a seller who actually has what he's offering for sale eventually ::) -


Should have included the Classic I put wooden scales on to

EvoWood 14,EvoWood S557 and Special Mechanic with DIY scales
-
-
@Wootz said:
Kirk, I like your Special/Jr. Mechanic mucho
Do you have a pic of the backside?
Yeah, we is butt men after all.

Would like to see them jaws too if you can get a shot of them laying sideways with the jaws open. Wonder if Wenger & Victorinox pliers have changed much throughout the years? Also curious as to the the difference between the two company pliers are - past the slip joint.
-
@Xelkos said:
Kirk, I like your Special/Jr. Mechanic mucho

Do you have a pic of the backside?
Yeah, we is butt men after all.

Would like to see them jaws too if you can get a shot of them laying sideways with the jaws open. Wonder if Wenger & Victorinox pliers have changed much throughout the years? Also curious as to the the difference between the two company pliers are - past the slip joint.
Gents,I will do,but it will only be next week

-
A used Spartan getting some new walnut scales put on. Have plans on sending this to a relative who is struggling. Hope this will make her day brighter.
Still have to tackle a lanyard for it.
-
-
@lowtech said:
Do i know that Spartan by name, Maybe?
If so, send my best wishes along with it.
It does look really nice with the wooden scales.Yes, it is the Spartan you sent. And the wood scales came from WoodMan. Figured if it would help make another person's day brighter. Had plans on sending a note with it to explain where the knife and walnut scales came from, to give it some lore.
The wood scales I had made came loose on one side, so went ahead and removed them. Put on those laser-cut walnut scales instead. Was curious as to how they would feel, and they snapped right on!
Bit of lore for the gift. At one point in time I was adopted within mom's side of the family. In my early 20's had met my 3 half-sisters. Had tried to stay in contact but we didn't have email back then, and them girls were wild.

Last winter their mom, my biological mother, passed on. Through a lot of searching had found where she was laid to rest. Needless to say the known relatives were all but not helpful. So.. contacted the cemetery, left my personal info with them, and asked them to give that to my half-sisters (with explanation).Earlier this year was contacted by two of them via cell phone. Hard to recap 30+ years in an hour's of talking. Two have facebook, the middle & youngest. The middle gal, Sonya, was looking over my knife projects and new attempts at lanyards. She actually like them.
Though I told her of this forum, and of the many gifted individuals here, she says she likes them cause they were made by her big brother. That sort of hit home. She's going through a rough time of it too. Between that and reading here in the MTO forums how one got their first SAK through a relative, an idea was borne.
So, to wrap this up, I wanted to give her something to remember me by through the years. With the help of your Spartan, and WoodMan's scales, and a lanyard I have yet to tackle, felt it would be a good gesture to send her something she could cherish through the years - maybe even pass on to one of her children.

-
Swisschamp with Cambara hardwood scales. The Swiss cross is engraved and has one layer of 24ct gold leaf and is outlined with black acrylic paint. Not the most beautiful, but it took me forever to finish...

-
Factory-made: 54 Wengerinox model 1951 Soldier, unknown wood
and Victoria with blade type 297/11, likely walnut
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
) Who doesn't love some hardwood and SAK's?? 





