Micra Malfunctioning.... HELP!
-
Because if the resolution of the pictures (and my general lack of knowledge of how good a fake might be made of the Micra), I can't say for certain that this is a genuine Micra. I assume it is.
If you open the tool, and start to apply force to close it, is there a specific point where it begins to catch?
If so, check the blades there to see if there's a burr or something. Nock off the burr with a sharpening stone if that's the case.
Also, try mineral oil or 3-in-1 oil on the hinge pivot. Work it in.
Also, also, you could try manually opening and closing the pivot about a hundred times, to see if that eases the problem. I might make more drastic suggestions if all of these fail.
-
I'd start off with the obvious first ... clean it in hot water, dry it thoroughly and then re-oil it. Next, check for any dings/burrs along the cutting edges. Have you been "load testing" them - seeing just how strong they are by cutting heavy stuff or wire? If so any little nick or bruise in the cutting edge could be enough to get it to stick.
-
@Lynn LeFey said:
Because if the resolution of the pictures (and my general lack of knowledge of how good a fake might be made of the Micra), I can't say for certain that this is a genuine Micra. I assume it is.If you open the tool, and start to apply force to close it, is there a specific point where it begins to catch?
If so, check the blades there to see if there's a burr or something. Nock off the burr with a sharpening stone if that's the case.
Also, try mineral oil or 3-in-1 oil on the hinge pivot. Work it in.
Also, also, you could try manually opening and closing the pivot about a hundred times, to see if that eases the problem. I might make more drastic suggestions if all of these fail.
Asking due to my lack of knowledge about knives in general, what's a burr? (I am new in this SAK-collecting business and 13
) -
A burr on a blade is a tiny spot where the metal's been bent out of place slight by a localised area of very high force eg cutting through a very hard wire might cause a burr on a plier or scissor blade.
-
Have you tried repeatedly smashing it with a large hammer? I don't really have a solution, wait for more answers. :)
-
And this is why I don't like Micras :)
I would try the clean, oil and working it back in. On par with most other advice.
-
Mine does this when a bit grimmy :-\
-
Yup I had a micra that did that when I cut anything like tape and it goes gummy. Ive never been a fan of them personally as I prefer SAK scissors, and leatherman mini pliers based tools like the P4.
-
PROBLEM SOLVED!
Turns out I overhyped a lot... :ahhh :ahhh :ahhh :ahhh
I gave the "clean, dry, oil" tactic a try, and surprisingly enough, after putting it in a bowl of hot water and drying with a towel, the scissors started working again...

So yeah, my Micra is now ready to work.

-
Good to hear, TurkTeen

Enjoy :D
-
5 minutes later, and the problem persists.
It is oiled and waitting in the bathroom closet now, I will check it when I am back home 6 hours later.
-
Keep us posted mate

-
After 6 hours of keeping It in the bathroom closet, Micra now works properly. Several hours have passed since then, and no problems yet except for the oily feeling I get every time I touch the tool.
NOTE: I used a few drops of machine oil total on a few places, it works :)
-
spray some breakfree on that thing and you won't have the issue any more...that stuff is nuts.
personally I don't use any thing on my tools unless it needs it...which is usually rare with any of my leatherman tools. =)
-
@Metropolicity said:
And this is why I don't like Micras :)I would try the clean, oil and working it back in. On par with most other advice.
you don't like the Micra?!? :o :o
its one of my fav keychain tools of all time.
-
Lol, great that you managed it :D I was also about to say that it does that when veeeeeeeeeery dirty (I did that to mine once). But even if it hadn't worked, you should've approached Leatherman with the warranty claim - they're awesome even when it comes to the tiny keychain tools.

P.S. - it's interesting that yours was grimy out of the package.....
Or may be I didn't get something. But I haven't slept all night long, so I'll be forgiven.. :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login