And so it begins.... (My adventures into Alox!)
-
@nj2656 said:
That's a shame about the Cadets. Well maybe you'll go back to them later. Really was hoping for a Jr. Have you done a double opener/Phillips on a Farmer? If so do you have a picture?Well if I figure out a better way to build them with the pivots I'll continue. The scales are so thin that its really hard to counter sink the screws and still have pivot in the scale. I get about 0.010" in the scale and its really annoying to get it just right. I also have to use a coutersink bit on the pivot itself to get the screw to fit. It takes about double the time to build a cadet vs a pioneer so its really annoying. What I should do is look for shallow button heads so they might stick up from the surface a bit, but much easier to build and stronger in theory. I could mill a small recess say half way through the scale, then the button head could sit in that... hmm ya I like that idea much better. :D
I sent more scales for white cerakote, and 4 sets were cadet scales, so I'll at least build 4 more black/white cadets. :D
I got the stand unboxed and roughly in position. It needs to be leveled and bolted to the floor next.


The guy recommended an engine hoist to lift the mill onto the stand... I haven't figured out how to get that up there yet but if the Egyptians built the pyramids with primitive tools, surely I can lift a 400lb mill 4 ft vertically...

-
Do you know any contractors you could borrow a winch from?
-
-
Do you know any contractors you could borrow a winch from?
Nope, all my friends work in IT. :D There is an equiptment rental place near me though, I think I'll see if they rent hoists.
how about a floor jack? there should be one in the car with the spare tire, it will take some time but theres a few ways to do it! JR
-
New toys.... very exciting

-
A simple a frame and a pulley. Classic but it will do the job. :jealous: :(
-
@tattoosteve99 said:
A simple a frame and a pulley. Classic but it will do the job. :jealous: :(Ive got time to figure something out. It's an MT2 taper so I have to get a collet set still, so its not like I can use it yet anyhow. I got one ordered though, and a drill chuck. I need a vice still too, but eventually I can do something cool. :D
-
After over a month it finally arrived. My Danish Cadet with old school scissors modded by the very Syph.


Props Robert, you do some fine modding!
-
You should have included installation in the purchases price, but I guess that is part of the fun. :p
Also, if Syph really is getting out of the 84 game, I can heartily recommend PTRSAk for 84 alox with wenger tools (and Vic tools too). He did a bang up job on 2 cadets for me. The list of modders seems to be rather dynamic!
-
I could have peened it myself, but I wanted a 84mm threaded pivot knife so I gave Robert a go. :D
-
I just had a thought that you might be able to utilize. Making a locking SAK in the style of those old French shepherd's knives and Navajas with a pull ring.

I'm not sure you're familiar with these. They use the lock back style mechanism to lock the blade in place when open but don't have the part that you have to push to open the lock. Instead they use a split ring or sorts to pull the backspring up to release the blade.
Basically it would require one of your custom backsprings and a slight alteration of the stock blade pivot area.
(one of my famous MS Paint masterpieces :D )

What do you think? Possible?
-
Oh for sure that's doable. Interesting idea!

-
FINALLY, after 3 failed hard anodize attempts I have red hard anodized scales and liners again!

I did a mirror polish on the edges and the crosses and engraving plates and that did the trick this time. Previous attempts the red wasn't taking on some spots and it was getting really frustrating. So, for all those waiting on my red parts, I finally have them again! :D
The liners turned out really nice as well. Todays build with be black oxide tools with red liners, so it should be a nice look.



And here is the result of the experment of, can I hard anodize the regular cellidor cheap mystery grade of Al... kind of!

They mostly turned out right, except this one looks like it got some viral outbreak. I suspect the alum boiled through a coating on this liner of some sort. If I surface sanded it before anodize, that should have prevented the issue.

Cheers! :D
-
I deployed a set of red scales on a farmer. I still love the read and shiny brass look.






-
Oooooh, those look great!
Sent from my HTC One using Tapatalk 2
-
Here's a new combination that I put together last night.
This is the first time Ive used the OD green cerakote. This one has hard anodized red liners and black oxide tools. I even made the spacer washers for the phillips out of 0.030" nylatron (which is black) to blend in nicely.
SAKs look best when photographed outdoors in the sun! :D





-
Very nice indeed - love to the toolset too

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
