Leatherman QC Fails
-
No problem on the thread hijack. We like it when threads develop like conversations in real life do. Very few threads stay on topic here. And mods are usually those who do the hijacking. ;)
-
I can't believe this response. Leatherman USA would have replaced it without question. The customer is always right; you have a right to be happy with the money you spent. Whitby should remember who they represent.
-
I've just tried Matts test with my 2 Rebars, and they don't stick at all.
-
BigMatt: I had a similar issue happen to mine after using the wire cutters to cut some clotheshanger wire, for me, though, it stopped sticking after a couple days, so unfortunately, I cannot offer a remedy of the problem. I hope Leatherman USA can do you better. :/
-
To Leatherman US:
"Hi there.
Could you have a look at this video:
Leatherman REBAR problem.I would like to know your opinion on this issue. Apparently there is quite few rebars like that out there (there is a thread about this on multitool org) and we are curious what is your opinion. You might also take it as a fedback/field test from your devoted customers :-)
Kind regards"
One on 4th and another one on the 5th. No reply so far....
Just got a replacement for my Surge from Whitby for the cutters I managed to damage, no questions asked. Where is logic in this? -
b
-
I'd love to take a saw and chop open a faulty plier head to see whats going on in there. :D
-
-
Another QC fail on the latest Wave. The file and particularly the saw are now lying much deeper in the handles making them more difficult to get out. This is unacceptable for a new model. Apparently they have changed to a new press which has resulted in deeper handles. This should have been spotted and corrected before allowing to pass QC. I am thinking of cutting a small piece from a plastic clip and placing it inside the handle to prevent the saw going too deep, so I can easily get to the notch.
The date codes are now on the side. -
@hennypenny said:
Another QC fail on the latest Wave. The file and particularly the saw are now lying much deeper in the handles making them more difficult to get out. This is unacceptable for a new model. Apparently they have changed to a new press which has resulted in deeper handles. This should have been spotted and corrected before allowing to pass QC. I am thinking of cutting a small piece from a plastic clip and placing it inside the handle to prevent the saw going too deep, so I can easily get to the notch.
The date codes are now on the side.Hmmmm deeper handles may mean the rebar head can sit on the chassis along with the scissors. think
-
@hennypenny said:
Another QC fail on the latest Wave. The file and particularly the saw are now lying much deeper in the handles making them more difficult to get out. This is unacceptable for a new model. Apparently they have changed to a new press which has resulted in deeper handles. This should have been spotted and corrected before allowing to pass QC. I am thinking of cutting a small piece from a plastic clip and placing it inside the handle to prevent the saw going too deep, so I can easily get to the notch.
The date codes are now on the side.[Hint]Just stop biting your nails[/Hint]
:D :D
-
I've seen this issue with the Wave before. I don't think it's deeper handles, as that would be a major revision requiring new stamping dies. I believe the stops on the underside of the file and saw are being ground off too short. At least my file on my last wave had that issue, causing the nail nick in the file to be well below it's opening.
-
Another QC fail on the latest Wave. The file and particularly the saw are now lying much deeper in the handles making them more difficult to get out. This is unacceptable for a new model. Apparently they have changed to a new press which has resulted in deeper handles. This should have been spotted and corrected before allowing to pass QC. I am thinking of cutting a small piece from a plastic clip and placing it inside the handle to prevent the saw going too deep, so I can easily get to the notch.
The date codes are now on the side.Hmmmm deeper handles may mean the rebar head can sit on the chassis along with the scissors. think
Love your thinking :D
-
Another QC fail on the latest Wave. The file and particularly the saw are now lying much deeper in the handles making them more difficult to get out. This is unacceptable for a new model. Apparently they have changed to a new press which has resulted in deeper handles. This should have been spotted and corrected before allowing to pass QC. I am thinking of cutting a small piece from a plastic clip and placing it inside the handle to prevent the saw going too deep, so I can easily get to the notch.
The date codes are now on the side.Hmmmm deeper handles may mean the rebar head can sit on the chassis along with the scissors. think
Love your thinking :D
This means buying a new wave. Where to find a 2013 one for a good price.
-
When did they switch dies???? My Jan. 2013 is the same as my 2012 wave..... well the frame is the same anyway.

-
My date code is 0313 and its stamped on the inside wall of the handle.
-
</topic/45441
-
The diamond file on my new Charge AL is rubbing on the inside of the handle, causing the black finish to be rubbed off. Is that acceptable?
-
It's pretty standard. A lot of Waves/Charges suffer from that. The liner lock pushes the file outward towards the scale and sometimes it rubs against the handle. That's why my first question in the thread about the new design changes on the Waves was if they switched sides of the file.
Some pics would help to see if it's worse than usual though.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login