And so it begins.... (My adventures into Alox!)
-
Very interesting, can't wait to see a final result! JR
-
Looks very good.
What size is the checkered pattern, bigger, smaller or the same size as the Vics? Maybe a side by side pic. :D -
@enki_ck said:
Looks very good.
What size is the checkered pattern, bigger, smaller or the same size as the Vics? Maybe a side by side pic. :DThat pattern is bigger since I only had an 1/8 bit to work with. I think it will work ok for big knives, but if I was to texture say some brass 58 scales I would want smaller. The problem of course is that smaller bits have shorter cutting life. I'm still playing around, but its fun coming up with ideas. :D
-
Looks very good.
What size is the checkered pattern, bigger, smaller or the same size as the Vics? Maybe a side by side pic. :DThat pattern is bigger since I only had an 1/8 bit to work with. I think it will work ok for big knives, but if I was to texture say some brass 58 scales I would want smaller. The problem of course is that smaller bits have shorter cutting life. I'm still playing around, but its fun coming up with ideas. :D
Yea, I realise now. :D I was too lazy to do the imperial -> metric math to figure out what size bit it was. Did it now, 3mm. ;) Looking forward to see this progress.

Yesterday I was browsing through my photobucket library and saw this sketch I made some time ago. ;)

Soon I think.
-
Looks very good.
What size is the checkered pattern, bigger, smaller or the same size as the Vics? Maybe a side by side pic. :DThat pattern is bigger since I only had an 1/8 bit to work with. I think it will work ok for big knives, but if I was to texture say some brass 58 scales I would want smaller. The problem of course is that smaller bits have shorter cutting life. I'm still playing around, but its fun coming up with ideas. :D
Yea, I realise now. :D I was too lazy to do the imperial -> metric math to figure out what size bit it was. Did it now, 3mm. ;) Looking forward to see this progress.

Yesterday I was browsing through my photobucket library and saw this sketch I made some time ago. ;)

Soon I think.
Ya about 3mm. The channels are about 2mm apart though since only the tip of the bit is used.
I know that clip idea will happen eventually! There are just way too many things on my todo list to try. I still need to fit a fero rod on a bushcrafter SAK too. :D Lately Ive been getting more requests for a 58 with pliers, which is why I went back to figuring that mod out. A rambler with a pair of pliers stuck in the middle of it, would be a popular mod it seems.

-
Are the 1/8" scales thick enough to hold some T&T? I hope not because I wasn't a fan of Alox but then became one when I saw you mods. Now all I need is money for a 58mm with pliers, a regular 91mm with the factory scales and a 91mm with your home brew scales with T&T. Thank you a lot for making me poor'er

Hope you're making good use of you mill!
-
Are you using coolant? Makes for a nicer finish and longer tool life.
With small work like this, a trigger spray bottle would be sufficient, no need for a pump.A round tip conical carbide bit might get you a narrower pattern than a ball end.
3rd from the top -
@PTRSAK said:
Are you using coolant? Makes for a nicer finish and longer tool life.
With small work like this, a trigger spray bottle would be sufficient, no need for a pump.A round tip conical carbide bit might get you a narrower pattern than a ball end.
3rd from the topOh no that was just cut dry. I was only messing around to see what spacing would look right. I first tried a 45 degree end mill, and that did not work well at all. What I think I might try next is a staight end mill, but tilt the head 45 degrees. That should cut nice V slots.
-
My latest is a farmer with scissors and a small serrated blade. I can testify that the serrated blade shreds though flesh very well. ;)
The serrations were cut by hand, and then I used a belt sanding sharpener belt to put an edge back on the non serrated side. Worked out great. :D





-
Nice job
JR -
I got a few black oxide parts in yesterday....

A bunch of stormtroopers are going to go together for sure, and some 58 ramblers with brass scales.
I even made up some keyring spacers from 410 stainless so I could do stormtroopers with keyrings.

-
I'll take one BO scissors. ;)
-
I dont think Ive done hard anodized blue scales with black tools before, so here is one.
I even made a keyring nub from stainless 410 and had that BO'd with the keyring.





Cheers. :D
-
I don't think I've posted in your thread yet but nice work on all this ALOX stuff Robert. I don't have an ALOX SAK yet but I swear to you that I will get one of yours one day soon.
-
Black 'n' blue ;) Very nice

-
Wow my son would love that black and blue! Maybe I will get 2 one for each boy. Black and blue, and green and black.
-
Alright I know I say this a lot but that's my favorite one yet.

-
@tattoosteve99 said:
Wow my son would love that black and blue! Maybe I will get 2 one for each boy. Black and blue, and green and black.Blue and green hah, same here, if we ever have to get two of the same thing they have to be one blue and one green. LOVE the color combo Syph! Perfect fit! GREAT job! JR
-
Email sent.
wolfstyle
-
And now for something completely different.
It's a Vic and Wenger merger into an alox frame.

I wasnt sure about the pliers, but after some handle reprofiling, the parts mockup seems like it will all work out.





I should be done tomorrow if it works out as I expect.
Cheers!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login