The 30 Day Victorinox Huntsman Challenge!
-
Another great thread Jothra
The only thing that's confusing me at the minute is where the word challenge applies :D I'm pretty certain Vicky will be fantastic! -
At first, Day 2 looked pretty bad—it was Mud City on-site, and I was worried I might end up getting disgusting for an hour, then running out of work and getting sent home. In fact, it was so muddy that I wanted to tie my boots extra tight so I wouldn't lose one on the way across site to the tool trailer. So thumbs up for the hook! Recently I've been carrying a Wenger, and while I enjoyed that knife I didn't realize how much I missed the hook.

Also good for skates, climbing shoes, and anything else you want very tight!To help deal with excess water in the building, we brought a garden pump...but it didn't work. The good news is they're easy to take apart. The bad news is the pump wasn't just plugged, but actually broken broken. Of course, we had to take it apart to find out!

Phillips screws? Ha! I laugh in your general direction!Somewhere in there I picked up a sliver. It was one of those tiny ones that hurts an awful lot, but not enough to keep co-workers from making Waaaaambulance jokes. The tweezers tweezed.
The bigger stuff came in the afternoon, when I had to pick up a pallet of poly sheeting for under a concrete floor. This is 10mm sheeting, which is ridiculous, expensive, and moronically heavy. Vicky couldn't do the lifting, but it could do the cutting so I could lift the rolls myself.

The blade handled all the scary, beefcakey banding holding the rolls to the pallet.
It also handled the tangled mass of cellophane wrap.
Meanwhile (or, rather, after), the scissors cut through the last of the (plentiful) white banding that held the rolls to each other.Finally, with the monumental task of detaching these things done, and with the rolls lifted to their various temporary homes, I had to break down the pallet so it could fit in the garbage bin. This doesn't involve sawing the entire thing up; instead, I just saw about halfway through the main supporting 2x4s, and kick the whole thing in half. This is easier than it sounds, and usually only takes a minute or so.

I find this easier than cutting plywood. For real!Now Vicky is helping slice some Swiss cheese. Hopefully you don't need pictures to know what Swiss cheese looks like.
There we have Day 2!
-
Dang right out of the gate, Vicky is doing well.
-
Go Vicky!

-
Ha! Any LM would have fallen apart by now :ahhh :D
-
Good work!

-
Nice, another good day of work for Vicky

-
Okay, sports fans, here's Day 3! I didn't get all the pictures I would have liked today, but that's what happens when things get too busy.
First thing this morning, we needed to lay out the poly sheeting I picked up yesterday. This basically meant unrolling it from foundation wall to foundation wall, cutting it to length, and taping it together. Naturally, Vicky can't tape things (no thumbs), but cut the 10-mil plastic just fine. This included cutting out around pipes and columns so everything is nice and flat.
Next I needed to clean out the holes in the foundation that the rebar for the floor is epoxied into. Normally this just means using a pump-style blower to, you know, blow dust from the hammer-drilling process out of the holes. Unfortunately, seven of them (yes, I counted) were caked with mud, and needed some...um...probing. Usually I use discarded welding rods or long junk nails for this kind of thing, but challenge challenge challenge challenge!

Challenge challenge challenge challenge! Also, note the classy odometer reading written on my hand. I have a notepad in my wallet 100% of the time, so why was I writing on my hand?I tried to use the back of the blade for the scraping, since I needed very little pressure, and because a blade stuffed in a concrete hole barely bigger than itself is unlikely to close up. Phenomenally unlikely.
Anyway, I was pretty sure this was finally going to render the blade a bit dull, so I tested it on a receipt. It still sliced, but it wasn't a very clean cut. So, for curiosity's sake, I tried simply stropping it on my jeans, making 10 passes per side. The result? Please believe that I'm not making this up—the blade was push-cut sharp again. It can still shave arm hair, and I've done no sharpening at all beyond stropping it on my jeans. I'm actually getting a little afraid of the blade at this point. I'm scared that if I stare at it too hard, it will cut into my very soul.
When the hook of a co-worker's 50' tape measure got stuck open, I pried it into moving again using the awl. It was the only tool that would fit, I swear! Besides, everything's fine. Both tape and awl are unharmed.
At one point, I needed to pull a nail-it just far enough out of a wood form for my hammer to grab. So what happened? I accidentally pulled it all the way out with a single tug with the bottle opener. This picture is fuzzy because the nail-it started moving as my phone was focusing, and came all the way out just after the picture snapped.

I'm lucky I didn't fly straight backwards in a humorous cartoon roll to end up on my head at the bottom of a trench.Once we had the forms dealt with, we needed to snap some lines to mark our eventual floor-pour height. Step one was setting the benchmark height for the receiver of our laser level, so we could make sure the marks for our new lines were at the height of the rest of our lines. To make this as accurate as possible, I decided I needed something flat, with a point, to stick perpendicular to an old line to help me square up the bottom of the receiver's stick.
I just put the knife blade in place, set the shot stick on the blade, and used this setup to make sure everything was square. This was really easy and effective. I like easy and effective.
While actually snapping the lines, we found out our chalk line was fraying about 20 feet into the string, which meant it was getting snagged on its way out of the reel and on its way back in. Normally it frays closer to the leading end, so you just need to cut the string off at the frayed part, and tie the metal end back on. Twenty feet is a lot of string, though, so we trimmed the frayed parts down with Vicky's scissors. Success! I admit, this wasn't much of a challenge, but this is one of the few things I did today that didn't involve totally misusing my plucky Huntsman.
Hey, remember this?
That will probably go down in history as the worst thing I have ever done to a multitool ever. But I needed to pry that pin out enough to get a hammer claw under! What else could I do?
Oh yeah...this.

Maybe it doesn't show in the picture, but I'm putting a metric borkload of pressure on that bottle opener/screwdriver.I was positive this was going to end in tears. I thought, "moron! You're going to destroy your bottle opener on Day 3! You're going to be without one of the most important functions on your pocket tool for the rest of the month, you idiot!" Well, no. I was wrong. I was the wrongest boy in Wrong Town. I could pry the form pin out just enough to get a real prying tool under it, and Vicky's bottle opener left unscathed except for a couple of extremely hard-to-spot scratches. I could barely get the bottle opener under there in the first place, and I was sure I was going to either snap the tool right off or bend it beyond any hope of closing it again. What actually happened is that it still has exactly as much snap as it did before. I'm sure much more pressure would have wrecked everything. I'm absolutely shocked at this result. I don't even have the words, and I'm all about words. I wouldn't recommend doing this, but now we know you can.
Day 3 everybody!
-
I'm following this thread
I just bought a huntsman myself :)
thanks for the excellent topics Jothra
I enjoy reading your 30 day challenges
this one is one of the best so far

-
Again, another enjoyable read. Sounded like a bit of a rough day, but that seems to be the norm for you and Vicky so far. I loved the term, "metric borkload"
I seriously chuckled out load when I read that. -
This challenge is awesome. Really securing my condlfidence in Vic products.
Sent from my Kindle Fire using Tapatalk 2
-
You put a lot of good use into your multitools. I wonder how one of the Gerbers with a pry bar on them would work for you?
-
This is really cool Jothra, reading every day anxious to know how Vicky handled it.....

-
I have tried... and tried... and TRIED to tell people to carry a vic, if for NO OTHER reason than to have a good 'light duty' pry tool. You know, that thing that will save you from snapping off your blade tip by doing something stupid that most any scale flat driver can handle.
I may need to really reevaluate my assessment of 'light duty' for the vic's prying capability.
And now I'm wondering what an ALOX 93mm, Spirit X, or that big monster flathead on the 111mm could handle. :o
Keep this stuff coming. I'm a fan. I'm subbed. I've 'liked'. In the words of the Tick: "I grok your mouth music, mandingo!"
-
Great work for another day, totally unexpected, and still 27 more to go! Keep it up Vicky!

If only a LM could also try whatever Vicky is going thru, that would be the ultimate death race of the century...
>:D -
@Lynn LeFey said:
I may need to really reevaluate my assessment of 'light duty' for the vic's prying capability.And now I'm wondering what an ALOX 93mm, Spirit X, or that big monster flathead on the 111mm could handle. :o
I haven't used a 93 or Spirit, but I can tell you from similar (but not identical) experience that I would have had almost no reservations about doing what Vicky did with the Beef Monster prybar on my OH Forester. That thing is a beast from beyond purgatory.
Also: "Churchill's space ponies are making gravy without the lumps!"
-
Victorinox should be paying you !
-
- I will not take it easy on this tool. I have higher expectations for this one than my other two challenge tools, and I will punish it accordingly. I may do things to this tool that will make you cry (and, let's be serious, will make me cry).
:ahhh shrieks :ahhh I knew you were serious about that and in all honesty, sticking the knife blade into a concrete wall :'( ... Vic openers are absolutely great IMO and you just demonstrated why! I think you're kind of making History right now, writting a review that future generations will use as a reference regarding SAK limits

I'm looking forward to seeing what comes next (poor Vicky, you deserve better). Take care

-
This is like a horror movie, but our plucky heroine is still taking it in strides! :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

