The 30 Day Victorinox Huntsman Challenge!
-
Today, on a very Special Episode of Day 11, Vicky does a bunch of the usual cutting, slicing, prying, and scraping, then solves what could have been a Very Major Problem.
This morning, it was time to clean out column pockets in the foundation walls of another building on site. There were a couple of corners I just couldn't quite get my hammer claws into, so it's a good thing I have a friend with a bottle opener.

Fortunately, there were only four corners this tight.Now, if the guys pouring them in think of it, the anchor bolts get duct taped to keep concrete out of their threads. This was the case this time, fortunately.

Trust me, cutting off this tape is way easier than the alternative...I had to cut the tape on all 100 bolts, and Vicky doesn't mind.
Unfortunately, one anchor bolt in one column bucket was heaped at the bottom with concrete. Normally one can bust this out with a hammer directly on the top of the problem anchor bolt, but this one was one of the most stubborn I've ever seen. Fortunately, Vicky can pry and chip when needed, because my hammer couldn't reach back here.

Pry the...thing! Chip the OTHER thing!All of that excess concrete had to go before I could cut off the tape and call it clean. After what felt like forever but really wasn't, it looked like this:
It was a lot of work for Vicky, but it all got done, and the screwdriver/bottle opener is only a little more scuffed on the tip than before.
Finally, a few of the anchor bolts had twisted tie wire wrapped around them for some reason, much of it wound very tightly. Fortunately, I have a prescription that sounds an awful lot like "Mix hook and tie wire in end loops; just add twisting motion, then yank wire out for extra flavour".

See? Hook+wire+loops+twisting+yank=GONE FOREVER.Finally, we have this little gem between myself and a co-worker:
"Hey, stop the truck!"
"What?"
"What's that weird sound the truck's making whenever you start moving?"
"What sound? I don't hear it."
"Like rubbing paper or...just turn the engine off."I don't know a lot about motor vehicles, but I do know drive shafts shouldn't look like this:

This must be one of those new, experimental Tyvek drive shafts.I think maybe it's a wrapper from a lift of plywood or something. I'm not sure how it got wrapped so tightly around the whole drive shaft, and who knows what kind of mess that would have made if it had stayed there? As is, it took five minutes of hacking and slashing with Vicky to get that tangled mess out. There was no beginning and no end...ALL WAS TYVEK. It was so tightly wound that unwrapping was not an option, so it's a good thing I had a good, sharp pair of blades to play with. If this had led to some kind of breakdown, as the most experienced labourer on site, this probably would have come back on me.
Thanks, Vicky, for really getting me out of a bind. A lucky break on Day 11!
Edit—I almost forgot to mention that cutting all that Tyvek and banging on that drive shaft was hard on Vicky's blades, so I had to give them both an actual-for-real sharpening when I got home. A few seconds with a diamond file and a ceramic rod on each side of each blade, some stropping, and good as new!
-
This has been a very challenging day yet everything is still good. I'm impressed! :D
-
Sounded like a brutal day for Vicky, yet she emerged fairly unscathed

-
this thread is fantastic!
-

:D
-
I'm really loving this thread. I've got a feeling that in the midnight hour Vicky cries "more, more, more"
-
That's a "Vickytorious" day for Vicky!
It's the first time I hear Vicky saving a truck, that's quite a story to tell! 
-
Jothra, I was just curious...
Do your coworkers look at you like you're off your rocker when you stop to take a picture of your hand holding a pocket knife like 5 times a day?
Have you explained to anyone what's up with that?
Also, I think saving a truck from tyvek was worth the effort of resharpening. I'm not any kind of sharpening expert, and i find sharpening vic blades back to paper-cutting sharp a pretty simple task. One of the things I LOVE about vics.
-
No-one sees me taking the photos, because in these early stages of a building I spend an awful lot of time doing gruntwork on my own. It's just as well, since I'm just about the only person in the company who carries a multitool at all. It's kind of a joke around here, though I don't actually get it, since they're always asking for it.
-
Alright, Day 12, whaddaya got?
Well, a bunch of dirt ended up crammed between a foundation wall and its (all together now!) rigid insulation. Since it was already Hilti-nailed on, there were two schools of thought: rip the insulation messily off and spend $21 a sheet to replace three sheets, or very carefully pry the sheets off so they could be used again.
Option 3 (C or iii, maybe?) was the winner.

Cut around that anchor! Heave-ho, ye swabs!Yup! The simplest, least damaging route was to cut exactly around the anchors, and pull off the resulting nearly complete sheets. Good job, Vicky!
The only other significant event today was some plywood template stripping. We use plywood templates to suspend anchor bolts in concrete column bases, so when the pour is over the anchor bolts are already perfectly placed. The four bolts and the enclosed space of a column pocket made it really hard to pry the bottom piece of plywood out. Thank goodness for little knives with hearts of gold:

The section on the end got pre-cut by Vicky before prying.Day 12!
-
Go Vicky! :D
-
Vicky (or you ;)) were being clever with the insulation task
Only limited by our imaginations with these wonderful little tools. -
Go vicky!

-
Rain! Rainrainrainrainrainrainrainrainrainrainrainrainrainrain!
Rain.
What a day. Also mud, by the way.
Anyway, there were two things for Day 13. The first thing was nice and easy. The second thing was nice and easy provided you weren't Vicky. RUBRUC RED WARNING: don't do the second thing. It's bad. It's a bad, bad thing. Of course, it's not a first for Vicky, either, but whatever.
First up, Vicky's nice, non-conductive toothpick helped clean the mud out of a female grounding port.

Don't worry—the picture is not fuzzy because of high-voltage electricity. It just wouldn't focus.Next up, the chop saw's concrete blade was tight, and hard to put on the saw. All I needed was something like maybe a hammer or something...

Action shot again! Vicky can be very, erm, persuasive.It took seven bonks to get that blade down the spindle far enough to bolt on. Vicky suffered no damage from the incident.
-
It is so cool how much you can do with one good SAK.
I'm wondering on your thoughts on the best SAK for the job:
Clearly the Huntsman is doing a good job and most likely you wouldn't want less since you do use the scissors & the saw.
But do you want more? How about the Victorinox Ranger - same as the Huntsman + file (would that be a valuable addition for what you do?) on the main tools and there is a small flat screwdriver & a chisel on the back layer.
Would a chisel be useful for push cutting stuff?
Would the file be useful for cutting metal and deburring and filing?
Would the extra size & weight be a negative?I love my Cybertool because I do more with computers but I have a Ranger for taking camping and I really like the mix of tools it has. Reading the things you put your Huntsman through I can't help wondering if the Ranger would be the perfect SAK for your job.
-
I carried a Ranger for a year or two. I love its tool density, but I very rarely used the extra tools, except for filing my nails. It's an excellent carry, but since I almost never use the extra layer, I usually stick with the Huntsman instead.
-
@Jothra said:
I carried a Ranger for a year or two. I love its tool density, but I very rarely used the extra tools, except for filing my nails. It's an excellent carry, but since I almost never use the extra layer, I usually stick with the Huntsman instead.Yeah, you can easily put a Rambler on your keyring for a nail file and carry a lighter main SAK.
It sounds like for your needs the Huntsman may be the perfect SAK, just the right tools to do what you want.
I think that I need a file more than a saw, but that is just me.For someone that never needs a saw then the Climber/Climber II may be just right.
Then there is the Spartan - great for just the important tools if you don't use scissors ever.
This is one thing I love about Victorinox, they put out a bunch of different models and most people can find one that suits their needs perfectly. -
I carried a Ranger for a year or two. I love its tool density, but I very rarely used the extra tools, except for filing my nails. It's an excellent carry, but since I almost never use the extra layer, I usually stick with the Huntsman instead.
Yeah, you can easily put a Rambler on your keyring for a nail file and carry a lighter main SAK.
It sounds like for your needs the Huntsman may be the perfect SAK, just the right tools to do what you want.
I think that I need a file more than a saw, but that is just me.For someone that never needs a saw then the Climber/Climber II may be just right.
Then there is the Spartan - great for just the important tools if you don't use scissors ever.
This is one thing I love about Victorinox, they put out a bunch of different models and most people can find one that suits their needs perfectly.I can vouch for the Rambler's nail file as I've used either a Classic or Rambler for years for most all of my nail maintenance

-
Is Vicky still alive? I'm getting worried. ;)
-
enki_ck: how on Earth did you know to post that while I was in the exact middle of writing this post? I hit the preview button, and there you were! Dark hoodoo!
After a long weekend (Heritage Day yeah!), I've got A MONTAGE!
On Day 14, the only new or unusual thing I did was buy a new bike lock!

I know it's pretty low-security. When I need high security, I lug my Kryptonite New York Fahgettaboudit Mini).Vicky's scissors can handle zip ties. This shouldn't surprise anyone. This isn't nearly the worst type of zip tie a Huntsman has handled for me. No scissor issues so far, obviously.
Next up: goofy arts and crafts project on Day 15:
Transponder-enabled car keys are ugly. Now mine is ugly and has superglue-enabled thread to pretty it up a little (or at least make it stand out in a crowd). It was easier to stick the hook through, grab the string, and pull than to thread the string on its own. For the record, I started over, and now the top of the key is wrapped in purple.
Enough with the potatoes! Time for meat:
Remember how Coghlan had to pry out a few feet of broken tile from under a wall? Well, now (Day 17, actually) Vicky has pried a bunch of broken concrete chunks out from under some heavy-gauge steel track. It wasn't easy, but someone had to do it. Someone surprisingly like Vicky! The screwdriver still works just fine. There are a few more scratches, but nothing deep. A half-assed buffing could probably get them all out, if scars weren't a badge of Swiss Army Knife honour.
There's no photo, but on Day 17 my foreman needed to borrow Vicky to take apart and clean a powder-actuated nailer. More screwdriver action! He managed to barely make fun of me when he asked for it, too. Just calling me Macgyver once, without a bunch of laughing and poorly-assembled insult comedy, is a big step for him.
Day 18 (today) saw Vicky get up close and personal with me face. There's no picture, but somehow I picked up a tiny metal sliver in the front of my chin that didn't start hurting until about an hour after I'd been anywhere I could have received it. Fortunately, between the tweezers and the small blade, I managed to get it out (finally—it was tough to get!) without doing any damage to my meal ticket (I use my face for hammering nails).
Also, we were shimming under heating/cooling unit curbs on the roof (hot! Gah!) to level them. We used wedges to level them out so we could measure the gap underneath to size our final shims. What happened when the wedges weren't thick enough to level a curb?
I'm telling you, that screwdriver/prybar/bottle opener/wedge/scraper/Macguffin is absolutely the most amazing of things. This was also a test of the scales, since the back scale was helping support all that weight. Good news: no damage!
Now that the complications of the long weekend are over, and I'm back on the construction site, regular updates should resume like nothing ever happened!
Days 14-18!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login





