What Did You Use Your Multitool For Today?
-
The closet doorknob came right out in my hand this morning. And about 2.5 seconds later was securely replaced with my Wingman.

-
@Aleister said:
My little daughter came to me with a tiny toy part stuck inside a pen cap. After hitting the cap on my desk for a few times - with no success - I used the Explorer's corkscrew to grab and pull it out.
Not a life or death situation but, for a dad, his kid's "you are my hero" hug is better than anything :)I also used my self-locking pliers (unfortunately, closer than my upstairs Surge) to rise my older daughter's bike handlebars a bit, put the chain in place and pull the wheel back to tighten the chain.
Spoken like a true good dad!

-
The hooks on this lure stood no chance to the wave's wire cutters

-
Just used the PST's knife to open some mail here at work

-
Today at work the nozzle cover sensors on one of the tint machines decided to die. After a 30 minute call with tech support, I managed to get the machine to run without the nozzle cover in place, but had to remover the part to keep using the machine. The SI did some prying, unscrewing and poking, I did a fair bit of swearing, ;) and got the SOB working ok until a tech can get out to us, sometime early next week..... >:(
-
I used my juice s2 to remove an ancient electric heater from the kitchen of a house I'm doing some remodeling work on. It was a little add on job the guy wanted done. I removed a few long screws, four little nails and cut the wires powering it, then dogged them off.
-
Spirit X to fix up some toys. The joys of babysitting

-
... and later to mod the Mora 1 Classic a bit
-
Used my MUT to open two imported beers . Also cut some crap with it .
Chris
-
I used my LM Crunch and Rebar and the PocketWrenchII, today, while taking apart to bikes that were falling apart, so I can bring them to the big garbage depot thingy. Among others, I used the Rebar to cut wires, the Crunch's 1/4" bit driver for driving allen-screws, and the PWII to undo some bolts.
Also, earlier today, I used the knife on my Rebar to cut open some of the plastic strings around the packs of newspaper I got.
And just now, I used a the blade of my Vic Waiter that was on my desk to cut some cheese :)
-
Pocketwrench II to unbolt a couple exhaust clamps swapping out old rusted ghetto rigged muffler, for new slightly less ghetto rigged Dynomax muffler. Did well enough, Blue sounds substantially better.
-
Tool: Victorinox Spirit
Task: Taking off/re-install AC filter screen on ceiling ducts
Performance: Excellent. Classic multitool application--climb on top of ladder to access the AC ducts, only to find out there are phillips that needed to be unscrewed, wimp out the Vic spirit and the rest is history. :D -
Used my Rebar and Fisherman while fishing today. To much to list, but quite a lot of scissor and cutting tasks. The pliers got a good workout also.
-
Used my LM wave to remove some projectors from their ceiling mounts
-
Used my Surge to take apart, clean and put back together 2 Hoover sweepers, put a new end on a electric cord and scrap out the bowl on my Dr. Grabow freehand. And the day is young yet.
sent from Ducttapetech's mobile device
-
We've been in the midst of a major home remodel (since last Nov actually). Some of it with professional builders, some ourselves. We're doing the majority of the kitchen. My wife built all the cabinetry. I'm doing most of the electric.
Yesterday, we put in the island hood. Charge ALX, Atwood Crypto and Leatherman Crunch have been invaluable in this.

Saturday before the Hood

-
I used the spirit x to tighten the handle on a pan
-
I used the spirit x wire cutters to make a clean cut on the end of a fishing rod to put on a replacement guide ring. I was able to do it but the spirit design wire cutters didn't work well.
-
@Nhoj said:
I used the spirit x wire cutters to make a clean cut on the end of a fishing rod to put on a replacement guide ring. I was able to do it but the spirit design wire cutters didn't work well.Honestly the wire cutters are my only gripe with the Spirit X. The rest of the tool being perfect makes up for it though. :D
-
@captain spaulding said:
I used the spirit x wire cutters to make a clean cut on the end of a fishing rod to put on a replacement guide ring. I was able to do it but the spirit design wire cutters didn't work well.
Honestly the wire cutters are my only gripe with the Spirit X. The rest of the tool being perfect makes up for it though. :D
Yeah if they just didn't grind that extra notch on the wire cutters. Honestly I would prefer pointier pliers on the spirit but I'm fine with the ones on there. And yea the spirit is pretty perfect. :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login