My small adventure into 58mm SAK modding!
-
Ok here's something a little different. A brass scaled minichamp with one liner replaced by that aluminum toothpick and tweezer holder I made awhile back.








-
Cool idea!
-
Shiny!

How does the brass scaled one compare to a Cellidor Minichamp, width-wise?
I really like your 58mm work. Looking forward to the "Micro-Swissgrip" -
Nice to see you made this one happen.

Looking forward to the MiniMe PocketGrip. :D
-
@lowtech said:
Shiny!
How does the brass scaled one compare to a Cellidor Minichamp, width-wise?
I really like your 58mm work. Looking forward to the "Micro-Swissgrip"I wanted to take a pic of this one compared to a cellidor but I dont have any left. I think its going to be pretty close to the same.
The next 58 I post will be the finished prototype of the micro swissgrip. :D Pliers in a rambler with stock scales is the protype. Then I can make brass and Ti ones.

-
Thanks nonetheless. I really like your knives.
-
Here is a brass rambler (without keyring), with black oxide tools and screws.





-
Hmmm, that's certainly... different.
Not sure if I like it yet, but I'm thinking it's got something special, in a good way :) -
You're killing me with all these beautiful SAKs, there are not enough drooling emoticons to express how I feel.
BTW, hows the pliers mod going?

-
Some delicious customs here

-
Here is my first attempt at working with copper for scale material. This is a drifter with copper scales and a brass liner.



-
It´s looking good and will get better with age and patina.
-
Brass is excellent - Syph007...stunning work sir!
I was directed here from another forum to look at your work on SAKs and I can see why you were recommended.

kawasemi
-
I have been working on the 58 mm pliers mod off and on for awhile now, and I have tried so many ideas for locking the pliers that I have completely abandoned a 'simple' solution to this, and am just going to make the complicated version.
Since I was trying to make a mini wenger pocket grip anyway, I decided to make a locking mechanism similar to that one.
Here is a pic of where I am so far.

The diagram hopefully explains this well enough. I JB welded in a piece of drill bit shank into the pliers to act as the retaining pin.

Part of the liner will slide and hold the pliers shut. That part is roughed from 0.032" Ti and will be plenty strong. I got to use my mill to make that tang and slot and it worked out sweet. There is 0.001" clearance on those parts and they slide perfectly.
Stay tuned! :D
-
I knew it had something to do whit those pliers as soon as I saw this thread updated. :D Interesting decision with the sliding liner lock. You said a couple of times that galling of titanium against titanium is a problem. How are you handling it here with the to sliding liner parts?
And if that partial layer is sliding, what about the other layers that require the 4th pin?
-
You are correct any parts where Ti and stainless touch have to be carbidized, except the inner part of the lock as I want it to be sticky there.
I already prototyped the 3/4 pin split system and it worked fine. Basically if you picture a rambler with this layer in the middle, 3 pins will go all the way though, and the other pin will only hold its half of the sak together.
It was the only way to have the pliers down further inside the SAK, and it make the whole package a really nice keychain accessory. The downside of course is that its way more complicated to build.
-
Correct me if I'm wrong, and this is merely an I'm trying to understand it question, Wenger Pliers wouldn't work because its spring is activated by the layer spring (slipjoint one) right?
Can't wait to see it done, a would be amazed even if it used a simple bail that folded to hold the pliers,
the sliding lock just forces me to put on my "absolutely must have otherwise I'll die" list.Congrats for the amazing work Syph, you never ceases to amaze me, thank you for that!!
-
I finally got around to making a Ti 58 with tweezers on the back scale. Way more annoying then I thought it would be, but it does work. The Ti scales I use are thinner than standard ones so the tweezer head needed to be trimmed a bit, but it worked out ok.






-
NICE. Ti tweezers would be over the top.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login