Ranger Band Carry - DIY Minimalist Tool Retention
-
-
Thank you for all the supportive comments

Gareth:
I agree, if I have to use it many times a day, getting it in and out could be a little annoying. I have an office job and the job itself doesn't really require me to use the tool a whole lot, but I often think 'what good is my multitool if it is not on me?' So as a compromise, this is how this 'carry' comes into being. I will post more 'finer pointers' for making this DIY more robust and user friendly.Chako,
Wooo...now we are cooking. I know of a place locally that I could get all sizes of real earth magnet(or super strong magnet). I will see what I could come up with.
Tabasco,
Thanks for pointing the post out, good to see I am not alone here.
-
Hi, all.
As promised, I've been wearing this DIY everyday for a week now. So far so good, here is a 'interim report' showing how it works on different pants and belts:

Carry it with a 5.11 tactical pants, sometimes the width between the belt loops on pants might not be enough to accommodate a full size MT, so I do skip a loop on this. This is probably one of my go-to pants for lazing around on a couch, watching movie or doing errands. There is a open side pocket that might perfectly fit a MT or a magazine, but I never took my chances since the MT might just slip out. In case you are wondering, no, I was good and I didn't drop my pants that day(for skipping a loop).

For usual workdays, I wear a khaki and loose polo. This is how it looks on them. Usually, I wear a brook brothers khaki and how the belt loops situated was perfect for this DIY.

There was one day last week I have to dress up a bit for meeting with bankers, and I decided it was perfect opportunity for the BO Victorinox Spirit to get some belt time.
Another belt with jeans for another day.
I went for a short hike on a really hot day over last weekend(33C, 91F) with high humidity. To say the least, I think I might have my undie soaked thru and thru. Luckily, like any sheath, I was thankful this carry method was able to keep my Spirit dry.
-
The following are the finer pointers for making and using the 'ranger band carry':
- More robust design
- Details on a good fit
- Other suggestions
1) More Robust design
After a week of using the original, there is no sign of tearing apart, but fearing it might happen in the future, I rounded up all the perpendicular cut points for wear-and-tear prevention:



The last picture shown the difference between the new and original design.(Top: original; Bottom: new)2) Details on a good fit
I found how well this 'sheath' work will largely depend on how you cut it and what kind of inner tube you are using. For myself, I actually order a Avenir inner tube 26 x 1.90-2.125 from Amazon(original it wasn't for this project, but it turns out well


(pix borrowed on the net)
The inner tube should fit onto the belt very loosely, if it is already 'gripping' onto your belt, you'd probably have a hard time to stretch it over to cover the tool.If the band diameter is too narrow or the 'width' of the window you cut on the tube is too narrow, it might clam onto the tool a bit too tight and make difficult to get the tool in and out. I find a good compromise is about 1 inch of rubber covering the tool at each end, making it easy and secure enough to use for a few times a day.
For smaller MT or SAK trekker/GAK, I put two ranger belts(same diameter) onto where the rubber gripping onto MT at each side. Those two belts will constrict the diameter of the sheath and make it grip tighter onto the tool.
3) Other suggestion
-Like any other sheath, this works great especially if you are going outdoor and will get sweaty wet. I have seen many knife users complaining their tools get rusty in the past, when the tools were kept in sweaty pockets.
-Like your belt-attached cell phone or side arm, it might be advisable to move the tool so it is not affecting how your seat belt function or make it more easy to retrieve when you need it for emergency.
-For backpacking, this 'sheath' could be transferred onto your shoulder strap/belt strap easily, and move back onto your belt when you arrive camp.
-
-
Yeah, that internal radius on the cut-out section makes sense to me.

-
-
-
-
Hey, guys.
I just realize I have forgotten to put up the video link onto this thread. At the end of video, I kinda demo how the tool/knife is being put in and out of the sheath.
Ranger Band Carry DIY Minimalistic sheath for Multitools and Knives
Right now, there is something even more exciting being cooked up...it should be fun.

-
@Aleph78 said:
I would imagine you could use similar made out of a road bike tube for smaller tools, like 91mm Vic
Totally, and if you use a narrower tube, it is possible to use it to carry something round and smaller, such as a Minimag AA. But just in case you want to use the same size for everything, the last two pictures do shown a way to do it.

-
Nice video comis
I used a road bike tube, which is smaller in diameter, and it works great for smaller tools. -
-
-
Thanks for bumping this up guys.... that's a clever idea

-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

