JA,s OHT challenge.
-
The oht got put to the test today.
first this morning I installed two mailboxes with it using its Phillips and flat drivers also used the small driver as a awl again.
then it got to work on a old plow truck we keep running to abuse snowplowing. Pliers tightened the battery clamps flat driver to adjust the carburetor
after lunch me and the oht had a used home to install. The strap cutter cut the straps holding bundles of wood shims and it cut many feet of 6mil plastic. Also cut some wire ties .

What happened to the can of fruit you were going to open?
I'm gonna to take a can with me tomorrow. I had my lunch break at home today. Tomorrow I'm on the road. :)
-
I have yet to mod a file to fit into the oht's cleaning rod whole.
I did find that a normal flat file will not fit. I will have to use a round or triangle file.
I've been to busy to make one but I will when work slows down.
-
I have yet to mod a file to fit into the oht's cleaning rod whole.
I did find that a normal flat file will not fit. I will have to use a round or triangle file.
I've been to busy to make one but I will when work slows down.
Do you really need a file in your work environment?
I do.
i use it for smoothing out styrofoam skirting on homes also I work with metal duct work.
I try remove most of the sharp edges before I put it up
also making a clean metal surface for ground wires .a file is just handy for me in my tool .
its one less thing I can forget.
also if I just need to use it a little and its not worth carrying a full size one with me all day. :) -
I have yet to mod a file to fit into the oht's cleaning rod whole.
I did find that a normal flat file will not fit. I will have to use a round or triangle file.
I've been to busy to make one but I will when work slows down.
Do you really need a file in your work environment?
I do.
i use it for smoothing out styrofoam skirting on homes also I work with metal duct work.
I try remove most of the sharp edges before I put it up
also making a clean metal surface for ground wires .a file is just handy for me in my tool .
its one less thing I can forget.
also if I just need to use it a little and its not worth carrying a full size one with me all day. :)
-
@JAfromMn said:
I have yet to mod a file to fit into the oht's cleaning rod whole.I did find that a normal flat file will not fit. I will have to use a round or triangle file.
I've been to busy to make one but I will when work slows down.
Any chance the hole itself could be modified as a bit driver?
-
@bmstrong said:
I have yet to mod a file to fit into the oht's cleaning rod whole.
I did find that a normal flat file will not fit. I will have to use a round or triangle file.
I've been to busy to make one but I will when work slows down.
Any chance the hole itself could be modified as a bit driver?
Possibly, although I don't have an OHT.
-
No fruit today but I promise Il open a can dog food tonight .
I forgot it.
-
@bmstrong said:
I have yet to mod a file to fit into the oht's cleaning rod whole.
I did find that a normal flat file will not fit. I will have to use a round or triangle file.
I've been to busy to make one but I will when work slows down.
Any chance the hole itself could be modified as a bit driver?
you could make a bit driver that would fit but it would only work to tighten and its a small screw I don't think it could handle much torx.
-
Today 's oht action
It was very helpful getting a ac unit put in at work today
First I used it to remove the front panel on a furnace. The tabs holding it on are very stiff the first time there opened. The flat driver worked fine to pry it open.

its next task was to remove a screw I couldn't get at with the nut driver. Flat screw driver to the rescue

prying off the break away sections of the access panel for installing the ac condenser

after I got the ac in.
I needed to clip a large zip tie I used to hang the cable tv wires with.

and the last task I used her for was to twist a hydraulic jack release to lower a home.

I also used it to cut a bunch of plastic and tape I didn't get a pic of.
I never really cared for if my multitool had oh opening blades but it didn't take long for me to get hooked on the oh opening pliers and drivers.
I still carry my Chapman ratchet and bits but I use them alot less because the oht,s are so quick.
well I got to feed the dogs and myself Il post some pics of the can opener in action in a hour or so.
-
5000+ views
I'm very happy you all are enjoy my thread.
Thanks alot to all of you following.
I've enjoyed making it.

-
Wow a lot of action today!
-
I hope he didn't break the can opener on that dog food... :P
-
Sorry I'm so slow
pizza for me/Mrs.ja and gravy train for the doggies

the can opener works well I got the can open in about 20 seconds

it was smooth cutting and it was fun one hand open my can opener 8)more important to me the tool/coating held up to opening the can

sorry for the crapy pics
-
NICE! A little can opener action. Thanks JA!
-
I may have been slightly less than charitable in my views of the OHT previously (particularly due to the contentious way it is marketed)
;) but the bottom line is it is working very well for you, and quite frankly, that's what matters most
I still can't see it being a tool for me and my needs. I would have little need for a strap cutter and all those flat drivers, needing instead scissors and awl much more frequently, but that's not a "failure" of the tool in any way, just that it suits other people better than me :)One of my (and other people's) criticisms has fell on the shortness of the blade and saw, although in truth I have personally found the short blade on the MP700 to be perfectly adequate for many (urban) chores. We can see the length is rather stubby compared to the body of the tool, but is there any chance of comparison pics to the length of the blade & saw on a 91mm Vic and 85mm Wenger please anyone?

-
Il take some pics when I get home 50ft-trad its about in-between a 91 Vic and a Wenger 80whatever mm saw. Closer to Wenger.
I haven't found the blades and tools to short for any task I've used it for. So far.
there sort but work very well. You get a good grip. Comfortable.I think the folks at leatherman put a lot of thought into the oht. All the tools and functions it has that I've used work very well.
I wish they would make a more civilian oht its close to being a really great tool now. a file and awl are needed to make it a much better tool for every day use by normal working people. A scissors would also be nine but then I wouldn't have a reason to carry my micra :)
I love mine but I carry a tool box with me . :P
-
Thanks JA

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login