Wiha Micro-bits and Cybertool?
-
I've seen a machinist that I worked around use a neat trick with 1/4" insert bits. He would grind a shallow recess around the circumference of the bits. He would then add a o-ring to increase retention. It was a quick fix that seemed to work for him pretty well.
-
Long time lurker, finally decided to create a login, and ask a question about this subject (yes, its a thread that's 3 years old, I know)
What about putting a ball detent on the cybertool bit holder itself? It wouldn't be that hard (seriously considering doing it, as I love my cybertool 41 and carry it every day... but I'd love to have the option of carrying bits that I use, like a 1/8" hex). I don't think a strong magnet is a good option, electronics like key fobs and cell phones don't like them very much.
-
Hey, welcome!
That long driver is awesome eh?
Agree. I really wish there were more bit options. If there were, it would replace my Charge ALX as my around the farm EDC.
-
@DarthChicken said:
Long time lurker, finally decided to create a login, and ask a question about this subject (yes, its a thread that's 3 years old, I know)What about putting a ball detent on the cybertool bit holder itself? It wouldn't be that hard (seriously considering doing it, as I love my cybertool 41 and carry it every day... but I'd love to have the option of carrying bits that I use, like a 1/8" hex). I don't think a strong magnet is a good option, electronics like key fobs and cell phones don't like them very much.
That is an intriguing idea. I suppose you're suggesting one of the ball detent setups with the expanding spring-steel ring around the outside of the driver. Would this require anything other than a hole drilled in the driver for the ball, and the proper diameter spring?
-
I'm talking about a hole drilled in the side, just smaller than the diameter of a ball bearing.. toss in the ball bearing, a spring, and then plug the hole to hold the spring in place, either by tapping the hole and screwing a small plug in place, or simply peaning over the edge of the hole.
But yes, you're idea would work as well I believe, other than increasing the diameter of the tool itself a bit and having the driver sit a little higher outside the knife.
-
@DarthChicken said:
I'm talking about a hole drilled in the side, just smaller than the diameter of a ball bearing.. toss in the ball bearing, a spring, and then plug the hole to hold the spring in place, either by tapping the hole and screwing a small plug in place, or simply peaning over the edge of the hole.But yes, you're idea would work as well I believe, other than increasing the diameter of the tool itself a bit and having the driver sit a little higher outside the knife.
That would be brilliant!
-
After reading this I checked and several precision bit sets I have will fit in the cybertool socket. The most complete set I have that is sort of compatible is a 54 bit set from iFixit but I have one with ball end hex bits from Kronus as well. None of these make sets with double ended bits or ball bearings. An accessory I had not had that seems attractive for travel is the 14 bit holder at http://www.wihatools.com/700seri/751serie.htm
It is too bad that others don't make exactly compatible bits; double sided does seem like the way to go and the ball bearing works with the plastic do-hickey to hold extra bits in the cybertool.
-
@appletree_man said:
I think there was a discussion on SOSAK about this, if I remember correctly the Whia bits would have a problem as they don't have a built in ball bearing to hold it in the Cybertool driver.You might want to read this:
</post/743264>
All the bits you could ever really need, held in place too, for around $5 or $6. -
there's a company called http://www.facom.com they do a a range called "Bits Series 0" 4mm with ball bearing detent.
Page 436 of their catalog
Warning, could be expensive!
-
I recently got the Vic CT 41 and it was missing a few bits. I looked through the MTo pages and found this great thread regarding how to get set up with bits and not pay the high price for Vic ones. I looked through what I already had and to my surprise I had a cheap set that actually fit pretty well. You will have to do the shrink tube mod first so the bits will be secure but thats a small price to pay for having quite a lot of extra bits.
Now that I have my bits sorted I needed a way to carry them. I was going to use the small altoids tin but figured there was another way and again looked through what I already had laying around. I had a used krazy glue container that seemed good especially since I didn’t intend on needing 44 bits. The tube holds 18 bits but having to spill out the contents to locate the one bit I would need seemed like too much fuss. It turns out that the bit holder themselves actually work out great when one is empty and flipped and used as a cover. I determined 6 of my most used bits and then used an empty holder as a cover, if I need 12 bits then I can para cord 4 holders together and its not much larger than the glue tube but I don’t have the fuss of figuring out where the bit are I need. The bits I got were from wallyworld and I know I didn’t pay more than $10US, I also have some torx bits that I got from HF&T for cheap as well that fit pretty good ( keeping in mind the shrink tube mod ) -
i forgot to mention the cheap bits comes with a nice extension that reall yadd reach to your CT41
-
Nice find Aloha, I have that same set I got at Walmart for like $7 or something.
I did like the way you used 2 holders to cover top and bottom of bits, that was cool.I do wish the Vic bits were reasonably priced, but, sadly they are crazy high
-
yeah I wanted to also but the factory bits but not a 5-7 a pop. I searched and found this thread and sure enough I had the cheapy set. the reverse empty holder works out great and I don't think ill ever need more that 12 bits so an empty one flipped as a cover works great. the glue tube was clumsy as I had to empty it to get a bit. keeping the bits in their proper home makes its very handy and easy to locate just the right bit. what a great SAK and even better to have a wide assortment of bits on the cheap.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

