Problem With My Wave
-
I think that the little metal thingy that hold the knives closed when the pliers are open could be the culprit
-
yes. handle works flawlessly.
as mentioned the one side was stiff when i first got it last week but i oiled it and no probs. -
@detron said:
I think that the little metal thingy that hold the knives closed when the pliers are open could be the culpritNah, the knife blade is opening well past the stop for that. This will be hard to put into words but I'll try ...
The tang of the knife blade has a flat spot which engages with the liner lock when open, and sits at the top when closed. It seems to be that the angle the blade is locking at is when the flat spot has just passed 90 degrees, and the fully radiused part is passing the lip on the handle. I'd be looking for something fouling at that point and see if there's any gunk on that flat section (or start of radiussed point) that's fouling the edge of the handle.
Aside from that relube the blade and keep working it over the extent of travel it is comfortable with in case there's a bit of something that's wedge in under the pivot. Also open up the pliers handles and give the inner edge of the liner lock towards the pivot a good blast with WD40 (on both serrated blade and file), and again try to work this through. If the file is also struggling on the same pivot, it could well be a bit of grit that's got wedged under a blade somewhere and is overtightening it
.... though this is all just drunken speculation ;)
-
Try turning the saw/serrated knife pivot a bit by holding it on both sides. It should rotate freely. Then try opening the blades again.
Do you have torx t10 security (the ones with the hole) at your disposal?
-
No torx bit. Will have to find one.
-
I've had this happen before but can't remember how I solved it. :( It may have been related to the locking nub. And you need two torx bits, one for each side of the pivot.
Inside the handle there should be a lever that pushes out when you open the pliers and prevents the blade from opening by pushing a small nub inside the blade's thumb hole cutout. Is it still there or has it broken off? Maybe it's jammed somewhere.
-
This thing.


-
Thats totally bizarre. I had one issue kind of like this before. It was do to a malformed (as in it was not round) washer. As it rotated it jammed itself up real good and wedged the pivot. If that's not it, Im out of guesses. If you had sercurity torx bits it would be a quick diagnosis. Back off the pivots a bit and see. There could have alos been debris in there that just jammed itself in better too. Either way it;ll have to come apart or go for warranty.
-
That's pretty nasty Rick. It looks like it needs a strip down, clean and rebuild to me. If you do it, you'll void the warranty, if you send it in you'll obviously have to wait to get it back. Your call mate

-
The broken part I had in mine.

-
Yep she's going for a ride. I will look here at all yours photos while mine is away.
-
do you have any other multitools that you can use while this one is on vacation?
-
Yes I have others. ;) the kick and the wingman
-
You should email LM first about your problem.
-
I did email lm
-
@rickboone said:
I did email lm:)
-
@rickboone said:
Yes I have others. ;) the kick and the wingmanThat is good. I was going to loan you one if you did not have a backup. But you have enough to "get by" while your Wave goes in for surgery
-
Yes I have others. ;) the kick and the wingman
That is good. I was going to loan you one if you did not have a backup. But you have enough to "get by" while your Wave goes in for surgery
SURGEry, you mean?


:D :D :D :D :D :D :D
-
Yes I have others. ;) the kick and the wingman
That is good. I was going to loan you one if you did not have a backup. But you have enough to "get by" while your Wave goes in for surgery
SURGEry, you mean?

wow, hilarious!

that would have been twice as funny if it was a Surge

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login