Stranded wire cut off test
-
@ironraven said:
All that sounds about right. But I like nice pair of toenail clippers for this kind of thingNail clippers are an essential tool in any electrician's pocket :-)
-
Nail clippers, really? Are you two yanking my chain?

Sheesh, the things you learn on the internet. Any particular brand of toenail clippers?
-
3rdpig, I'm cross-linking your post on scissors vs. stranded wire in my Scissors Test thread, because this here is some excellent testing.

</post/786549>Thank you for testing both the plier head and scissors on stranded wire. As you (and others) may have guessed, I like testing threads.
-
The Splice was a surprise, I expected better from that. Unfortunately I'm not surprised with the Fit. It's not up to Gerber's usual standard on the scissors for some reason. The Squirt and Juice both surprised me in how well they did, and as I recall the Squirt did quite well in Cupboard's test on tie wraps too
It does however show that the tools will indeed do the biz on stranded wire, even if the wire cutters on the pliers prefer more solid media, and another reason why scissors should be more common on tools.Many thanks for this 3rdpig - some excellent info there buddy

-
@Lynn LeFey said:
3rdpig, I'm cross-linking your post on scissors vs. stranded wire in my Scissors Test thread, because this here is some excellent testing.
</post/786549>Thank you for testing both the plier head and scissors on stranded wire. As you (and others) may have guessed, I like testing threads.
Thanks for doing that Lynn, I like testing threads too and I enjoyed your scissors test.
@50ft-trad said:
The Splice was a surprise, I expected better from that. Unfortunately I'm not surprised with the Fit. It's not up to Gerber's usual standard on the scissors for some reason. The Squirt and Juice both surprised me in how well they did, and as I recall the Squirt did quite well in Cupboard's test on tie wraps too
It does however show that the tools will indeed do the biz on stranded wire, even if the wire cutters on the pliers prefer more solid media, and another reason why scissors should be more common on tools.Many thanks for this 3rdpig - some excellent info there buddy

The poor performance of the Splice surprised me too, I've always considered Gerber to be the best at scissors, but that's probably based on the excellent scissors on the MP400. Same with the Fit, which as I indicated in my post not only surprised me, but annoys me since I've been carrying it instead of my Cybertool but will have to do some more testing with it before I continue that practice, scissors are just too important to me on work days and I can't rely on the tiny scissors on my Rambler to do the kind of cutting I'd expect from the scissors on the Fit, Cybertool or Balance.
Glad to be of service!

-
How could the Splice fail?

-
Never had any problems cutting stranded wire with the tools I've carried, those being a Leatherman Blast, Core, SOG PPP and Bear Jaws Electrician.
While I carry a PPP these days, I do like the Leatherman better for stranded wire. The hard wire notch can easily strip wire if you use the right amount of pressure.
-
Great test
I'm going to do a similar test on bicycle brake cables 
Nice test. Thanks.
One of these days I may test a Leatherman Style PS on bicycle brake cables. Will it cut?
Doubtful :-\ ive tried the old and new wave on bicycle cables and its usually a bit of a challenge,usually i find old dumped bikes and remove parts so cutting cables can be handy,i will try a test

Just thought one problem could be the wire cutter cross instead of inline ,
I tested today the LM Style PS on cutting a bicycle cable and as expected I had no luck. The pliers slipped and were no able at all to cut the cable. :-(
With paperclips and electrical (copper) wire, I had no problems with this tool.
-
On the question of brand of toe nail clippers, anything reasonably beefy, but I wouldn't use them to take on something heavier than 18ga (or 22ga stainless!). They are also my favorite way of cutting zip ties.
It was a habit I got into in college, working in the electronics lab- small, cheap enough that if someone stole them I'd cuss, glare and replace, and there is no excuse for not putting the small, very conductive tool in your pocket where it can't short anything.
-
I sometimes have to cut reasonably thick (2mm ish) stranded steel wire, used for washing lines.
For that I use my ST300.
Even though the pliers head will just shred the wire, at the oposite side of the pliers head, between the handles and very close to the handles pivot point there is a deticated stranded wire cutter.
That works well and cuts the stranded wire cleanly.That feature is available in other LM models too.
-
My take on this, spurred by a discussion that went along the lines of
Cupboard: I think the Spirit wire cutters are crap
Magic Bus: I think the Spirit wire cutters aren't crap
Cupboard: (thinking maybe I'm just being mean to them) OK, I'll prove it.The contestants: Gerber: Dime; Leatherman: Squirt PS4, Juice CS4, Skeletool, Wingman, Rebar head on Wave, Wave head on Rebar; Victorinox: Swisstool Spirit X
The challenges: 0.2mm^2 1000V stranded equipment wire, 0.5mm^2 tri-rated stranded equipment wire, 0.25mm^2 horrible nasty yuck 2 core bell wire that nothing will cut properly, 2.5mm^2 tri-rated stranded equipment wire, 2.5mm^2 stranded conduit cabling (thick strands), 6mm^2 tri-rated stranded equipment wire, 0.75mm^2 3-core flex.
The scoring: as above pretty much. I wasn't quite as thorough I guess. I have pictures of everything so ask if you want them. I have included the marginally less boring ones.
- Cuts completely through with clean, smooth ends.
- Cuts completely through with rough ends.
- Cuts almost completely through to the point where a second snip would finish and be usable.
- Doesn't cut through, requires another cut or maybe two, leaves it a mess.
- Total failure, complete mangulation of the wire, no amount of retries will ever get it cut. You're better off chewing through it or banging it between two rocks.
Notes: I didn't always clear up the last MT's test pieces before taking the picture of the current one. If you see a picture of a load of clean cuts with a mangled bit at one side, that's the reason.
The results:
Gerber Dime:
0.2mm^2: 3
0.5mm^2: 3
0.25mm^2 bell: 5

2.5mm^2 tri-rated: 5. It just twists the jaws
2.5mm^2 conduit: 5. As above

6mm^2: Cutters too small
0.75mm^2 3-core: Cutters too smallSquirt PS4:
0.2mm^2: 1
0.5mm^2: 1-2
0.25mm^2 bell: 4
2.5mm^2 tri-rated: 1
2.5mm^2 conduit: 1

6mm^2: Cutters too small
0.75mm^2 3-core: Cutters too smallJuice CS4:
0.2mm^2: 1
0.5mm^2: 1
0.25mm^2 bell: 4
2.5mm^2 tri-rated: 2

2.5mm^2 conduit: 1-2
6mm^2:
0.75mm^2 3-core:Skeletool:
0.2mm^2: 1

0.5mm^2: 1-2
0.25mm^2 bell: 3. Almost certainly because they aren't very worn.
2.5mm^2 tri-rated: 2
2.5mm^2 conduit: 2
6mm^2: Cutters too small
0.75mm^2 3-core: Cutters too small

Wingman:
0.2mm^2: 1

0.5mm^2: 1
0.25mm^2 bell: 3: Given that the Wingman wire cutters were well renowned to be non brilliant and my decent bypass wire cutters at work struggle with this, the result is remarkably good.
2.5mm^2 tri-rated: 2

2.5mm^2 conduit:
6mm^2: 2, but more effort than others
0.75mm^2 3-core: 2. Very good considering it wasn't really big enough!

Rebar head on Wave:
0.2mm^2: 1
0.5mm^2: 1
0.25mm^2 bell: 2-3, about as good as it gets.

2.5mm^2 tri-rated:
2.5mm^2 conduit: 1-2. It cuts cleanly but the lack of clearance on the back side of the cutters tends to apply some squishage.

6mm^2: 2
0.75mm^2 3-core: 1-2

Wave head on Rebar:
0.2mm^2: 1
0.5mm^2: 1
0.25mm^2 bell: 3-4
2.5mm^2 tri-rated: 1
2.5mm^2 conduit: 1
6mm^2: 2

Was easier than the Rebar head, but tended to do this if you weren't careful:

0.75mm^2 3-core:Spirit X:
0.2mm^2: 3-4: really, this isn't hard to cut.

0.5mm^2: 3-4, as above

0.25mm^2 bell: 5, but then everything struggles with this. The only thing I can reliably cut it with in 1-2 goes is a pair of really good, really sharp side cutters.
2.5mm^2 tri-rated: 4. Pretty mangled but if you really kept at it you'd get there eventually.


2.5mm^2 conduit: 1-2: very good. The thick cores helped it.

6mm^2: Cutters too small
0.75mm^2 3-core: Cutters too small

The Squirt PS4 really surprised me actually. It was a very good cutter up until its jaws couldn't get round the fat stuff. The Wave cutters tended to go through more easily but the Rebar cutters cut with a more reassuring "snip". I think the Wingman is much maligned - it isn't all that bad.
Many thanks to Stephen (who I work for) for the bits of cable. Not that I've told him yet! They were all offcuts or second hand :)
Lastly: Al: all bar the Dime will happily grip an M10 nut, and that's the largest I can get my hands round the handles with. The Wave and Rebar both have similar placement in relation to the cutters due to the Rebar cutters being angled back.
-
Good test Cupboard. My findings are different, although I have not had access to a variety of wire like you.
I have had four Spirits, three of which cut stranded/insulated electrical wire well. The fourth Spirit did not due to a mangled soft wire notch caused by the previous owner. -
Not exactly standard wire, but my sog cut this stuff like nothing.



-
@Magic Bus said:
Good test Cupboard. My findings are different, although I have not had access to a variety of wire like you.
I have had four Spirits, three of which cut stranded/insulated electrical wire well. The fourth Spirit did not due to a mangled soft wire notch caused by the previous owner.Just out of interest, will your Spirits cut paper? Mine doesn't even mark it. It is entirely possible that my test above is being skewed by a dodgy Spirit. I have given my Wave (with the Rebar head) some stick, cut things it really shouldn't have cut and done silly things to the head... but it will still cut paper.
It's never going to be as good as some of the other tools because the wire cutter isn't as big. The design seems to be a bit strange to me too with the two notches.
-
I don't have a Spirit at the moment but my Swisstool with the same cutter arrangement won't cut paper, although it will cut stranded wire easily. I think the inability to cut paper is due to the twin notch arrangement that Vic use ie. there are no blades as per Leatherman etc. and whatever you want to cut has to be placed in one or other of the two notches.
-
Cupboard, do you own a surge or st300 with the dedicated stranded wire cutter?
-
no, but I do have a Core which does.
Was there something in particular you wanted me to try it on?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login