Show your slip joint's thread!
-
A couple of old small ones I found at a flea market. The Vic Farmer is there for size comparison.
Bigger one has a blade and a nail file. It has a refence to a portuguese fertilizer company on one side and a pic of the goddess Ceres on the other.Small one has a small screw/phillips driver, a bottle/can opener and a small blade.
I don't carry them, just like their look very much!
:D



-
Those are nice, useful for keyrings because of the bails

-
I like the bigger one. Looks like it could be a nice classy carry.

-
I'll try to get better close-up pics. I believe the bigger one is from 1960s/70s. I'll look into the engraving in the blades and post it here.
-
-
Arthur Wright and sons, spear point with rosewood scales.

-
Nice bits of kit fellas! :)
Sent from my Nexus 7 using Tapatalk
-
-
Found this thread on BF, on who makes what. May be of interest to some, despite not being complete or updated.
-
-
Buck 303, used (I was going to get a 301 but this popped up on eBay)
It appears to have been sharpened badly using a bench grinder, though for the price it was OK. I have now sharpened it properly. (that buck steel is harder than you think)It is a very good size for EDC, with 3 thick blades. Light and solid, good walk and talk.



See the comparison with a RR stockman, with 2 instead of 3 springs and liners between the springs. The RR has thinner blades but size wise they are about the same.


-
Nice knife.
I don't have a 303 (yet) but I do like the 301. Very solid, classic knife. -
@jerseydevil said:
Nice knife.
I don't have a 303 (yet) but I do like the 301. Very solid, classic knife.I have been looking for a 301 for a good price, for some time. It is a seriously sexy tool.
I am sure that it will be too heavy to actually carry, for me. The 303 seems like a much more realistic carry option.
-
-
Very nice, Detron. I really like Rough Rider Barlows, and that is a pretty one.

-
@jerseydevil said:
Very nice, Detron. I really like Rough Rider Barlows, and that is a pretty one.
JD,
have any knowledge about these bark pearl ones? I just thought it looked nice
-
Very nice, Detron. I really like Rough Rider Barlows, and that is a pretty one.

JD,
have any knowledge about these bark pearl ones? I just thought it looked nice
I did a bit of research on them, and apparently what you see there is actually the outside of a shell, unlike mother-of-pearl. They grind down the outside and polish it to give that effect. I've never seen one before, but now I want one. :D
-
Very nice, Detron. I really like Rough Rider Barlows, and that is a pretty one.

JD,
have any knowledge about these bark pearl ones? I just thought it looked nice
I did a bit of research on them, and apparently what you see there is actually the outside of a shell, unlike mother-of-pearl. They grind down the outside and polish it to give that effect. I've never seen one before, but now I want one. :D
I tell you I LOVE it! I paid $10 for it, but I just think it is so nice! I appreciate your digging, I found the same answers, but I did not see these for sell too much so I was not sure if they were limited editions or special runs. I will have to do more research on it.
Sent from my SPH-L720 using Tapatalk
-
I have a bit of a soft spot for Schrade/Camillus USA slipjoints so I got this, used, Uncle Henry 897UH medium stockman, SS, derlin handles.
The knife is used but unfortunately there is a large amount of side to side bladeplay on the main blade
Anybody know if it is possible to correct that? Can the bolsters be removed so that I can hit the pins with a hammer? Should I just hit the bolsters or put them in a vice?
The knife is nice looking and otherwise looks to be in good condition.



Interestingly it one of the older serialised ones, with a serial number R6375 inside the liners.
-
I have an 897UH just like that one, as do many. It was a very popular model for a long time! Your "Staglon" looks much more natural than mine, though, and is obviously older with the serialized liner.
As to your query about tightening the pivots--you don't have to disassemble the knife to do it. You can lay the knife on a hard surface such as a workbench, and "whack" it right at the pivot with a rawhide mallet. Put something such as a thick towel or a magazine between the bolster and the bench, and between the bolster and the mallet. Start with light taps and check tightness and walk-n-talk between each "whack".
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login





