What's your latest Leatherman?
-
Finally got my LM MUT :D



-
My new (to me) Leatherman Ukiah as arrived.

Broke out the Sharpmaker and put a nice edge on it, now I need to find some time to get outdoors and play with it.




-
I like the Sideclip.
-
@Dr. Bahn said:
My NIB BO PST arrived today:Unfortunately I seem to be incapable of sharpening it with my Sharpmaker and it is the same with my used BO PST CC. Did LM use a different steel or could it be because of the BO coating? Does anybody has got the same problem with older BO LM?

I doubt it's the coating, as I'm fairly sure BO isn't anywhere near as hard as the SM stones. It should abrade away normally. Is the edge bevel itself coated? Perhaps the coating is coming off and clogging up the stone.
It could also be the angle, as some PSTs I've seen have bevel sharpened in that are either at or greater the 20 degree per side SM angles.
If you'd like, I'd be happy to either sharpen or reprofile the blade for you on my Wicked Edge. I'm pretty certain the PST also uses 420HC, so it isn't likely to be a steel issue.
-
@CanadianLMfan said:
I like the Sideclip.Thanks! I put it there for scale, but it is a nice piece, isn't it?
I just scored a duplicate off Ebay for a good price, so I'm trying to decide which one I want to sell off to offset the knife's cost. Or maybe just to finance the next find.

-
@sticktodrum said:
I doubt it's the coating, as I'm fairly sure BO isn't anywhere near as hard as the SM stones. It should abrade away normally. Is the edge bevel itself coated? Perhaps the coating is coming off and clogging up the stone.It could also be the angle, as some PSTs I've seen have bevel sharpened in that are either at or greater the 20 degree per side SM angles.
If you'd like, I'd be happy to either sharpen or reprofile the blade for you on my Wicked Edge. I'm pretty certain the PST also uses 420HC, so it isn't likely to be a steel issue.
Thank you very much for your friendly offer, but I guess sending it from Germany to the USA and back again is a bit inconvenient for the problem. ;)
I think I just have to take the time and keep on sharpening for some more hours. :DNo, the coating itself shouldn´t be the problem. But maybe it prevents the blade from cutting well when doing a paper cut test because of the extra friction?! Even then I should get the edge hair shaving sharp under normal circumstances though.

The bevel itself is not coated and visually everything should be fine. I guess the angle of the edge is disadvantageous for the Sharpmaker. ???
-
@sticktodrum said:
Is the edge bevel itself coated?Okay, it really is the angle of the edge. Your question gave me the idea to paint the edge with a marker and use the Sharpmaker again. The result is that the paint is now away on the upper part of the edge and the lower part stayed painted. That means the ceramic rods don´t touch the actual cutting part of the edge yet. That is why it doesn´t become sharp. (Does that make any sense? It is difficult to explain for me in english. Sorry!)
-
No, that is absolutely correct. I was going there next, to use marker to show where material is being removed by the stone.
The Sharpmaker works if the edge is either the same angle or less than the stone angles, which is why I often make the edges a bit below 20 degrees.
You could just adjust how you hold the blade, trying to stay consistent. :)
-
-
I'd call that money well spent.

Where did you find it?
-
I got this ST300 from Chris/Magic Bus yesterday..
And this RadioShack E4 from Philty arrived today.. :)
-
@sticktodrum said:
You could just adjust how you hold the blade, trying to stay consistent. :)I am not very good at that, so I think I will just use the angle of the Sharpmaker for another hour. :D The lower part of the blade is already shaving sharp but the rest is still dull.

Thanks for your help anyway.

-
My squirt ps4 arrived today.
-
Red and I like it a lot!

-
Just won a KF4 on the Bay.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


