The 30-Day Rebar Challenge!
-
@JAfromMn said:
How do you think the rebar pliers work with the large cutters in the plier head.I haven't used mine but it looks like they might get in the way.
I really do like the wire cutters. I have used them and they work great.
I believe that the same cutters are used on all the leathermans with replaceable wire cutters.
Now quit using multitools for hammers

great thread so far Jothra I'm enjoying reading about this mid sized leatherman doing full size jobs.

It depends on the task that you're doing.

-
@Cupboard said:
Jothra: I can't recomend Ironclad gloves highly enough. I've put a pair of their Framer gloves through hell and back and they're a bit tatty but still going strong. They do offer ones with more protection but for my crewing work they were just right.Oh, finding gloves isn't the problem. Finding my brain is the problem. I am looking for a new pair of gloves, though. Thanks for the info. I think I can get those at my favourite tool store. Yay!
@JAfromMn said:
How do you think the rebar pliers work with the large cutters in the plier head.I haven't used mine but it looks like they might get in the way.
The pliers worked just fine unbolting the battery cover on the U-Haul the other day. No complaints.
But hammer is my middle name!
Ha ha! Just kidding.
It's actually part of my last name.
-
Day 4!
I put Evowood scales on my T814, but that means no tweezer or toothpick slots. Panic at the disco!Whilst playing around, I discovered that the same piece that holds the Victorinox toothpick in it scale will hold it securely next to the closed corkscrew. But it's too long! What to do? What to do?

What to doooooooooooooooooooooooooooooooo...The wire cutters cut through the toothpick like butter. Not like butter would cut through a toothpick—but you knew what I meant.

It's not much of a project, but the results seem good.This morning I couldn't get into my truck—it was frozen shut (hi, winter! Missed you!) I managed to chip enough ice with the small slot driver to get inside, and then managed to unstick the windshield wipers by prying with the pliers. The chiseling would never have worked without a locking driver, or at least a good slip-joint. Anyway, I made it to work on time! Thanks, Val!
A successful Day 4!
-
Wow, frozen car already? :( You must have a long winter to look forward too. :-\
Anyway; a very fun read as always mate, keep it up.

-
-
**Day 4!**The wire cutters cut through the toothpick like butter. Not like butter would cut through a toothpick—but you knew what I meant.

Anyways, when does the torture start? I want to see val fighting for her life

Yeah, she's pretty much lounging by the pool in comparison to what Vicky faced >:D Although being that close to water is a hazard for a Leatherman I suppose :P
-
**Day 4!**The wire cutters cut through the toothpick like butter. Not like butter would cut through a toothpick—but you knew what I meant.

Anyways, when does the torture start? I want to see val fighting for her life


-
But that bit of the cutter is at an angle so it's OK in my book. I can't get my hands round the handles if I put a nut in the jaws that's a problem due to the cutters.
I'm probably sound a bit like a stuck record on this aren't I?
-
Oh, goody, another torture test and one of a tool I'd like to try out!
Thank you, Jothra.
-
How do you think the rebar pliers work with the large cutters in the plier head.
I haven't used mine but it looks like they might get in the way.

Note that in this example there are 4 or 5 points of contact on the nut, and 2 of them are the cutters.Yeah, that was what I didn't like about the pliers too :-\
-
I don't seem to have a problem with the pliers. At least they're (the cutters) angled to allow for decent gripping.
-
I don't characterize as problematic the fact that the Rebar's cutters serve as part of the pliers' gripping surface, as pliers with non-replaceable cutters work in the same way (depending on the size of the stock being manipulated). The only caveat is that the Rebar's main plier surface is smaller than that of the Wave, for example (about 5 ridges on the Rebar vs. about 7 on the Wave). I bet that the Leatherman engineers have this one figured out. Mr. Sawman is right about the Rebar's cutter's being angled (unlike those of the Wave, etc.).
-
@Etherealicer said:
Anyways, when does the torture start? I want to see val fighting for her life
It'll get heavier this evening for sure, but in the meantime rest assured that chipping ice absolutely destroys lesser tools.
-
Thanks for the great answer to my pliers question.
-
-
@50ft-trad said:
How do you think the rebar pliers work with the large cutters in the plier head.
I haven't used mine but it looks like they might get in the way.

Note that in this example there are 4 or 5 points of contact on the nut, and 2 of them are the cutters.Yeah, that was what I didn't like about the pliers too :-\
Did you try using the needlenose pliers? The pliers are one of the most unused tools on my LMs, but it's nice to have them.
-
Am I the only one here, sitting on the edge of the chair, while waiting for the tales of a new days torture? :o
Sendt fra min HTC One med Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login