Leatherman CROC?
-
I think I'll try adding a wire stripping notch and may try stonewashing or other finish. Anyone else thinking of modding?.
-
Did anyone else find the Croc in their stores? ???
-
Jersydevil, do you own a hardware store?
No, I run an independent paint store. Every single day we get at least one customer who has gotten frustrated trying to deal with someone in the paint department of a Lowes or Depot and comes to us half expecting the same sort of "advice" and customer service. I've been selling paint and painting supplies for over 10 years. I have a pretty good idea as to what I'm doing...... :)
Well best of luck with the store. As a side note i used to mail invoices for four paint companies. Kwai, general paint, color wheel, frazee and there was a fifth but I can't remember.
-
Ok. Got my copy in today. Here are some comparison pics.
Right to left.
PTX s30v
PTX 154cm
PTX LE 6AL 4V Ti (005/100)
PTX 440
PTX 440 Smoke (BO)
LM 420
HTX outdoors clone
LM crocThe finish is a nice stonewash, but the edges are quite sharp still. The inside of the wrenches have a bit of the laser/water jet cut start and stop points.
The steel is thinner by about 30% than the piranha and the most obvious is the lack of hex hole and bit holder.
The jimping is a little different and as is the edge grind for the pry ends. It truly looks and feels like a budget OPMT, quite literally from the cutting bed to the tumbler to the grinder and then into packaging.
If these should go for about $10, I can see them doing well. Anymore and it would need a lot more work on tightening up the QC.
There is always a way, hack on!






-
Wow, that looks bad. :-\ Like a very badly made copy. :(
-
What were they thinking?

-
These shots actually remind me of the Atwood vrs. Navy knock off comparison Nate did some time ago. ( Atwood Prybaby vs the Navy 2001 Emergency prytool. ) Only the Navy ones looked better.
It's hard to believe those to are actually made by the same company. :-\ -
@Metropolicity said:
Ok. Got my copy in today. Here are some comparison pics.Glad the package made it to you safely (I hope safely)
-
Oh gods, that is fugly.
Tim, it's time to take the boy to the woodshed. I know you want time off, but...
-
@ironraven said:
Oh gods, that is fugly.Tim, it's time to take the boy to the woodshed. I know you want time off, but...
Alas, I must agree with you :-\

-
Oh gods, that is fugly.
Tim, it's time to take the boy to the woodshed. I know you want time off, but...
Alas, I must agree with you :-\

Agreed.
-
Doesn't LM understand that most of us don't care for these on piece tools?
They don't need to make this many just because they ran out of ideas for MTs.
-
CanadianLMfan,,,,I must respectfully disagree. I see one piece tools(OPT) as fertile ground with much potential. Ever since Gerber created their Shard(which MT.O sold BTW). And I'm not a big fan of Gerbers, but even I carry a Shard.
What saddens me is that LM is squandering a great opertunity. And alas, the Croc proves that point, hence it should be renamed the "RUNT". So the present designers need to do some rethinking on their part. Or have the designer actually talk to fulltime OPT makers.
-
@derekmac said:
LM, MAKE SOMETHING NEW AND COOL! Don't do a cheap copy of your own tool!
Sent from my iPhone 5 using Tapatalk
If it wasn't for the remodelling of the Surge, which on the whole looks like a promising refinement even if it is a cost management exercise too (even though it's too big a tool for me), I'd be getting very worried about Leatherman right now. Quality declines, introductions of budget tools, venturing into new product lines that few seem interested in are all signs that would normally have me concerned about a company's long term stability.
The Surge's refinements do however seem well thought through in terms of the tool itself and of cost management, so maybe they're going to start phasing in more "refinements" rather than banking on the one-piece "gadgety crap" market to see them through any hardship. Maybe they'll even consider making an affordable Juice type tool with the quality issues addressed

-
It is thinner but has anyone tried using it. I use mine it works just fine. I used it to take the bolts off of the railing and to pry on a couple things just to see if it would flex or break.
-
@BIG-TARGET said:
CanadianLMfan,,,,I must respectfully disagree. I see one piece tools(OPT) as fertile ground with much potential. Ever since Gerber created their Shard(which MT.O sold BTW). And I'm not a big fan of Gerbers, but even I carry a Shard.
What saddens me is that LM is squandering a great opertunity. And alas, the Croc proves that point, hence it should be renamed the "RUNT". So the present designers need to do some rethinking on their part. Or have the designer actually talk to fulltime OPT makers.
I have no use for OPTs.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login