The 30-Day Rebar Challenge!
-
Bang goes any sleep tonight

-
-
This thread has got me carrying my rebar after work most nights.

I am almost ready to say leatherman is on the right track with the new multitools that have been coming out. I can't say that because the wingman /sidekick and all the stupid one piece tools.
The rebar and st300 are improvements over the tools they replaced.
they aren't going totally backwards.
-
Five Updates!!!

-
Day 10 was a pretty low-key day for Val. The large drive/prybar opened several cans of powdered tempura paint. The same driver helped me break into my own supply cupboard, for which I had forgotten my keys. It's about as secure as a safe made of low-grade Swiss cheese, so I pried it open, and later used the pliers to bend the latch back into shape.
-
Don't take this as a criticism,but I can't help thinking that Queen Vicky is looking down from her place of honour and thinking what an easy time Val is having!
-
@Jothra said:
Day 10 was a pretty low-key day for Val. The large drive/prybar opened several cans of powdered tempura paint. The same driver helped me break into my own supply cupboard, for which I had forgotten my keys. It's about as secure as a safe made of low-grade Swiss cheese, so I pried it open, and later used the pliers to bend the latch back into shape.Wait, what happened to the five updates?

-
Day 10 was a pretty low-key day for Val. The large drive/prybar opened several cans of powdered tempura paint. The same driver helped me break into my own supply cupboard, for which I had forgotten my keys. It's about as secure as a safe made of low-grade Swiss cheese, so I pried it open, and later used the pliers to bend the latch back into shape.
Wait, what happened to the five updates?

+1

-
I fell asleep on on my keyboard. I could have posted "adsgnjetiiiiiiiiijjjjjjjnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn etc., but how lame would that have been?
Day 11 was a strange one, because I didn't have the Rebar with me. It was, however, in the grubby hands of a friend who needed it more at the theatre than I did at work.
First they needed to cut a bunch of newspaper from big roll-ends to cover the walls of a scabby cardboard house (everything the lost boys build onstage is pretty scabby). Nice clean cuts, and no sharpening needed.
Next, the blade cut a hole in a tablecloth so a hose can run from a glass through the table below. This was an easy job, but apparently all the utility knives at the theatre were missing. So it goes.
Now, I know I'll misuse my tools if it means getting a job done faster, but even I cringe when I hear that they used the main blade to open cans of house paint. Aargh! Shockingly, no damage! When I first heard this one, I was expecting a blade shaped like a Big Mike banana.
So there's my absentee Day 11!
-
Back in my hands for Day 12, Val had something stupid to do: pound a hole in a table!
To drain a glass so it looks like Tink is drinking it, we needed a hose running through a table. The only problem is that the hole needed to be half an inch wider than the largest drill bit we had! So one guy drilled a hole, but he wasn't going to get anywhere trying to ream it wider with his drill.
If only I had a tool with a reamer in it!
Oh, yeah, right.
I didn't end up using the reamer. The table is HDF or something, but Val's blade was equal to the challenge. After some serious scraping and gouging, the hole was big enough for the hose, and we were ready to poison us some fairies!
I stropped the blade. It still hasn't needed a full sharpening.
-
-
Day 12 was full of hard jobs that were not at all urgent, and easy jobs more urgent than escaping from a room full of angry house cats.
The first job wasn't theatre related at all. I found a broken discman in a box whilst unpacking, and started playing with it. It wasn't working, so I used the fine driver to open the unit up. The larger screws were no problem, but the tinny ones on the inside needed a very fine driver (I stole the one from my Evo 17). I'm not sure why—I'm a lot better with analogue technologies than digital ones. Anyway, after taking the whole thing apart and putting it back together, I finally realized that it was the CD spindle that was broken, so rather than a Leatherman Rebar I needed boring, useful ol' superglue. Lesson learned: check the external stuff before going ape nuts with a screwdriver!
So Val is good for normal electronics screws, but not little tiny ones. That's pretty common with multitools, but it is too bad.
Back at the theatre, I had to trim a coroplast flat to keep it flush with the next flat over. I used Val, and then for the first time needed to give the blade a quick sharpening with a ceramic rod. Now it's good as new!
I has to tighten two wheel casters, which were both Robertson screws. I managed to get a decent grip on the screw heads with the pliers by sticking one tine in the hole and pinching hard. Nice job, Val!
I also had to tighten an eye bolt, so I use the small screwdriver as a lever, and spun the bolt. It was tough going, but it worked, and no damage!
The easiest but most frightening issue was with my costume—someone tied the drawstring at the neck with that experts call a Dorkbag Hitch. I had about 30 seconds to get it undone so I could fit the shirt over my giant monster of a head, but nothing doing. It was permanaknotted. This is exactly why I always make sure to know where the nearest knife is. It's also a good thing I had sharpened the blade maybe an hour earlier, because two quick slices and I made it onstage just in time, albeit short one drawstring.
Whew! Thanks, Val, for saving the day on Day 12!
-
@Jothra said:
Now, I know I'll misuse my tools if it means getting a job done faster, but even I cringe when I hear that they used the main blade to open cans of house paint. Aargh! Shockingly, no damage!Finally some abuse

I would have to be 30 flavours of desperate before I'd start opening paint cans with the knife blade of a tool with a prybar in it.
-
@Jothra said:
Now, I know I'll misuse my tools if it means getting a job done faster, but even I cringe when I hear that they used the main blade to open cans of house paint. Aargh! Shockingly, no damage!Finally some abuse

I would have to be 30 flavours of desperate before I'd start opening paint cans with the knife blade of a tool with a prybar in it.
+1
There's abuse and then there's stupid abuse >:(
-
Now, you wouldn't think I would have to spend so much time fixing beds, but that's theatre for you.
On Day 13, the metal headboards on two of the beds on-set were starting to get really loose, and it turns out haphazardly installed tie wire was the culprit. Fortunately, Leatherman pliers are fantastic at tying wire.

Just let me adjust that tie for you...Step 1 was to get rid of the old wire. This was actually easier to break than untie, so Val did some bustin' up. Step 2 was making sure the frames were at the right height to keep them from dragging on the floor (pictured in the...pic...ture. Good sentence there...) Third was to wrap twice on each side with doubled-up wire, since a single wrap per side would let the frame rock like mad, and doubled-up wire is, naturally, stronger. Now, in theory a saddle or butterfly tie would work best, but I cheated and ran the wire through the bolt holes on the frames, so it should be good to go.
The Rebar pliers flex a lot less than the Wave ones when twisting wire, especially when the wire is doubled up. I often grab wire with the sides of the plier jaws instead of the tips because I'm afraid they'll snap off, but with the Rebar I didn't bother. They are, as bicycle periodicals are so fond of saying, horizontally stiff and vertically compliant. I like. I like yes much.
Day 13!
-
Two Day 12s! :ahhh :ahhh :ahhh
-
Given he's already said he fell asleep on his keyboard doing one of the updates, I think that can be forgiven :)
I get the impression that using the Rebar isn't all that much of a challenge, it's doing too good a job >:D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
beer...