Waiter Alox
-
Well, for the corkscrew, you'd need a fourth pin, which comes out right in the shield, if I recall it correctly... So it might not be as easy as it seems.
So, how important is the corkscrew for you? You could always keep it with just the Bantam...
-
Ya the corkscrew is a pain to put on there. Remember its much thicker than the thin alox scales so it will stick out very far. The 4th pin isnt an issue though as it doesnt need to be exposed to the outside. Its only purpose is to prevent the spring from moving along the line of the knife, it serves no other point at all so just drill into the scales 2 mm or so and that will be fine to have a floating pin inside.
Just going with a bantam of course is much easier. :D I think youd just need to add a keyring to that since you want to carry that way.
-
There's a reason why you get Bantams in Alox but no Waiters...
-
@Syph007 said:
The 4th pin isnt an issue though as it doesnt need to be exposed to the outside. Its only purpose is to prevent the spring from moving along the line of the knife, it serves no other point at all so just drill into the scales 2 mm or so and that will be fine to have a floating pin inside.Thanks @ Syph007.
The corkscrew is essential to the project I'm afraid. I've browsed a lot before posting so have a good feel for how the finished tool will look and acknowledge the 'sticky out' corkscrew.
How do you stop the floating pin falling out? Just a friction fit (a reuse of one that has been drilled out), adhesive or threaded?
-
The 4th pin isnt an issue though as it doesnt need to be exposed to the outside. Its only purpose is to prevent the spring from moving along the line of the knife, it serves no other point at all so just drill into the scales 2 mm or so and that will be fine to have a floating pin inside.
Thanks @ Syph007.
The corkscrew is essential to the project I'm afraid. I've browsed a lot before posting so have a good feel for how the finished tool will look and acknowledge the 'sticky out' corkscrew.
How do you stop the floating pin falling out? Just a friction fit (a reuse of one that has been drilled out), adhesive or threaded?
I have pics of the one I did, I'll dig them up for you. All you need to do is use a liner as a template and drill the holes inside the scale just a tiny bit. I used a broken drill bit for the actual pin since it was nice and rigid that way. The pin is held in just by the scales. A little trickier to assemble but it works fine.
-
Found them.

To make the bottom of the hole nice and flat, drill a bit with a regular bit, then file the tip flat and use that to bottom out the hole. Then I just used that same bit as the pin since I wrecked it anyhow.
-
@Syph007 said:
The pin is held in just by the scales. A little trickier to assemble but it works fine.Right, got it - the pictures explain perfectly.
Would you be able to point me in the right direction for pivots/torx screws - more the spec than a supplier (diameter, threading etc...)? I'd prefer this than peening pins.
Have ordered my 84mm Waiter and Alox Bantam so this project is a go!
-
Knifekits.com and texasknifesuppy.com both have pivots. However I don't know about how much shipping would be to the UK
Sent from my iPhone using Tapatalk
-
@tattoosteve99 said:
texasknifesuppy.com have pivots.Thanks - I had a look on Texas Knife Puppy and couldn't find a single picture of a dog holding a blade :D
Seriously though, do you know what sizes I would need (length and diameter) - in mm if possible?
-
@tattoosteve99 said:
I would just get the 1/2 inch ones and then cut down to size. Easier to have to much than not enough :)Measure twice, cut once!
In 2.2mm Outer Diameter (or imperial equivalent)?
-
texasknifesuppy.com have pivots.
Thanks - I had a look on Texas Knife Puppy and couldn't find a single picture of a dog holding a blade :D
Seriously though, do you know what sizes I would need (length and diameter) - in mm if possible?
These are what I buy.
http://www.knifekits.com/vcom/product_info.php?cPath=60_83&products_id=471
Everything has to be drilled out to accommodate them, but it does work well.
Shipping is alot for sure though. I usually save up orders and get lots at once to make it worth while.
-
Thanks - this thread invaluable:
http://forum.multitool.org/the-mod-squad/my-attempt-at-building-an-alox-mod/I think too expensive to get shipped from the US - and I'm an impatient chap!
From what I see, I will require 4X 2.2mm rods with 3 out of the 4 tapped to M1.6 thread. Length to be confirmed. Is this correct?
I can get 2.2mm brass rod easily and cheaply enough but will need to buy the required drill bit and tap for the lathe (which is not a problem). Do you think brass would be sufficient if A2 steel screws used (they should almost meet in the middle)?
-
Are you talking about turning the brass rod into pivot barrels?
If you can get 2.2mm brass rod, you can use that directly without the need to drill/tap it. Cut it to length, file it flat and peen it together.
-
I can forsee that going disasterously wrong on my 1st attempt at Alox scales. I know where I am with machining parts.
Given that, are my dimensions correct? Will brass work as a threaded pivot?
-
Yes it works fine. I had a friend make me some on a lathe.

I just bought a 50mm long 3mm brass tube with a 1mm hole. Let's see how easily I can turn this thing into threaded pivots (Aiming for M2). :D
-
Thanks @ crackout.
According to the chart for an M2 you are looking at a 1.6mm drill hole to then tap it:
http://www.carbidedepot.com/formulas-tap-metric.htmYou might get away with tapping it to M1.6 without further drillng if you took it slow and steady with the tap.
Do you think there is any market for 2.2, 2.5 and 3mm threaded pivots? I might consider doing a run on the lathe and selling them on if there is. Having browsed the forums there does seem to be some difficulty in obtaining them, especially in Europe.
-
@Peso said:
Thanks @ crackout.According to the chart for an M2 you are looking at a 1.6mm drill hole to then tap it:
http://www.carbidedepot.com/formulas-tap-metric.htmYou might get away with tapping it to M1.6 without further drillng if you took it slow and steady with the tap.
Do you think there is any market for 2.2, 2.5 and 3mm threaded pivots? I might consider doing a run on the lathe and selling them on if there is. Having browsed the forums there does seem to be some difficulty in obtaining them, especially in Europe.
A market for pivots? You have no idea how many people want these :). Just about every modder here and then some. Better make a couple thousand
Sent from my iPhone using Tapatalk
-
Thanks @ crackout.
According to the chart for an M2 you are looking at a 1.6mm drill hole to then tap it:
http://www.carbidedepot.com/formulas-tap-metric.htmYou might get away with tapping it to M1.6 without further drillng if you took it slow and steady with the tap.
Do you think there is any market for 2.2, 2.5 and 3mm threaded pivots? I might consider doing a run on the lathe and selling them on if there is. Having browsed the forums there does seem to be some difficulty in obtaining them, especially in Europe.
A market for pivots? You have no idea how many people want these :). Just about every modder here and then some. Better make a couple thousand
Sent from my iPhone using Tapatalk
Someone tried that before remember and it didnt work out. I cant remember who now
, but he just gave up after trying a few times to have some made.He was asking if I wanted some but I prefer the treated steel ones. I get them fro $1 each in bulk so its hard to beat that. Brass I would find hard to trust long term since it can bend so easy. Is tapping 2.2 stainless that much harder? That is so tiny Id want to build a SAK and stress test it to see if it held up ok.
Edit: It was papercut
-
@Syph007 said:
Someone tried that before remember and it didnt work out. I cant remember who now
, but he just gave up after trying a few times to have some made.Yes, I saw the thread - the difference in my case is I would be doing them myself. I need to get tooled up to do it so I was wondering if I could recoup my costs by sharing the love. ;)
Ha. Yes, it is much, much harder. Beyond my facilities/skills.
@Syph007 said:
That is so tiny Id want to build a SAK and stress test it to see if it held up ok.I would agree if it was hollow rod, but with an A2 stainless screw in a threaded rod the brass is really just acting as a collar and the torsional strength is actually coming from the screw rather than the brass. I suspect a solid (rather than hollow) 2.2mm rod would be adequate (it looks like that is what used as factory fit). Brass is good for pivots due to its 'self lubricating' properties (I suspect you already know this).
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login