Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Question about getting my Swisstool cleaned/fixed.

Scheduled Pinned Locked Moved Swiss Army Knights Forum
7 Posts 1 Posters 1.9k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. Question about getting my Swisstool cleaned/fixed.
Question about getting my Swisstool cleaned/fixed.
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • mashguy4077 Offline
    mashguy4077
    Posts: 796
    mashguy4077 Offline
    mashguy4077
    wrote on last edited by
    Quote Reply

      I have a Swisstool which I carry everyday. The best multitool I have ever used, but lately a couple of the tools pull out along with the one I actually want out. Could that just be because of dirt/grease in the tool?.

      If so would dunking it in warm soapy water and scrubbing it down take care of that?. And if I do that how do I dry the whole thing out so I dont have to worry about rust. I dont have a blow dryer or access to an air blower, and a rag wont get down inside there very well.

      Also when I try to use the ruler it is supposed to stay in position, but for some reason it flops down and I have to hold the handles out to keep them straight while I measure something. What would cause that to happen?.

      1 Reply Last reply
      • Fattsgalore Offline
        Fattsgalore
        Posts: 883
        Fattsgalore Offline
        Fattsgalore
        wrote on last edited by Fattsgalore
        #1 Quote Reply

          The anti corrosion/oxidation properties of Victorinox's steel is high. With all the things you have to worry about rust really isn't one of them. As long as you don't dunk it in salt water or anything acidic your fine.

          As far as warm soapy water, yeah that's your best bet. Work the tools while it's submerged then finish off with your preferred oil. I use 3 in 1. I brush oil on, I no longer apply oil drops. Just leaves oil down in between the tang and liners with no real purpose other than collecting dirt and debris.

          If this doesn't work, WD-40 it over night and repeat the cleaning process.

          1 Reply Last reply
          • sticktodrum Offline
            sticktodrum
            Posts: 815
            sticktodrum Offline
            sticktodrum
            wrote on last edited by
            #2 Quote Reply

              Indeed, a good cleaning will do it well. I just leave my Vics drying near an open window and it works well. I personally just use a little of the Victorinox oil on my Swisstool Spirit.

              "If you put Bacardi in my glass again and try to tell me it's rum, I will burn this bar to the ground!"

              -A paraphrase of something I read, to which I related strongly.

              1 Reply Last reply
              • bmot Offline
                bmot
                Posts: 4,468
                bmot Offline
                bmot
                wrote on last edited by
                #3 Quote Reply

                  I actually once dried an MT in the oven... :whistle: So if you want to be sure it's dry, you could try that ;)

                  A knife-carrying guide for the international traveller. : http://forum.multitool.org/index.php/topic,47532.0.html

                  Merit Badges
                  EDCSource Buyer Mod User Flashlight
                  1 Reply Last reply
                  • Etherealicer Offline
                    Etherealicer
                    Admin Team
                    Posts: 12,034
                    Etherealicer Offline
                    Etherealicer
                    Admin Team
                    wrote on last edited by
                    #4 Quote Reply

                      I always put my SAKs into the Dish-washer.

                      It wouldn't be the internet without people complaining.

                      1 Reply Last reply
                      • tosh Offline
                        tosh
                        Posts: 3,181
                        tosh Offline
                        tosh
                        wrote on last edited by
                        #5 Quote Reply

                          @bmot said:
                          I actually once dried an MT in the oven... :whistle: So if you want to be sure it's dry, you could try that ;)

                          I've done that loads of times, better still - whilst its hot spray it with WD40.
                          I bought a tti cheap, in a real bad state. Scrubbed it clean with hot soapy water and scotch brites, dried it completely in the oven for 40min, then removed it and soaked it while it was still hot with WD40.
                          It looks amazing!!!

                          I don't claim to know it all, but what I do know is right.

                          1 Reply Last reply
                          • Aloha Offline
                            Aloha
                            Global Moderators
                            Posts: 31,235
                            Aloha Offline
                            Aloha
                            Global Moderators
                            wrote on last edited by
                            #6 Quote Reply

                              I'll echo giving the swisstool a good warm or even hot water bath and moving the implements while doing this. dry off as best you can and spray with wd40 and you should be good to go. I follow up with a good lubricant. I got 3 pretty well used swisstools and they all got the same treatment and were in great condition afterwards.

                              Esse Quam Videri

                              Merit Badges
                              One Piece Collector Japanese PST Juice Collector Level 1 Reviewer Camping Fire Making Flashlight Outdoor Cook BO Tools Level 3 Santa Traditional Folder Challenge Pen Challenge
                              1 Reply Last reply

                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                              With your input, this post could be even better 💗

                              Register Login

                              1. Home
                              2. Tool Talk
                              3. Swiss Army Knights Forum
                              4. Question about getting my Swisstool cleaned/fixed.
                              Reply
                              • Reply as topic
                              Log in to reply
                              COMMUNITY LINKS
                              EDC-TV SAKWiki GearFeed SAKSelector
                              Operational Funds

                              Help us keep the Unworkable working!

                              Make A Donation
                              November Goal: $300.00
                              Due Date: Nov 30
                              Total Receipts: $0.00
                              Below Goal: $300.00
                              0% funded
                              • Login

                              • Don't have an account? Register

                              • Login or register to search.
                              • First post
                                Last post
                              0