Budget EDC, Upcycle / Reuse to save money
-
@Etherealicer said:
Key WalletHave a spare key wallet? Take it apart. Its a great source for extra small locking carabiners..
I like this one a lot.

-
Key Wallet
Have a spare key wallet? Take it apart. Its a great source for extra small locking carabiners..
I like this one a lot.

ME TOO! thinking about buying a new one to rip apart!
-
-
Old Swiss rifle grease capsule all cleaned and pretty. Before and after, one down 2 more to go.



-
@Etherealicer said:
Old Swiss rifle grease capsule all cleaned and pretty. Before and after, one down 2 more to go.Totally jealous of those. those look great!
-
@Etherealicer said:
Surgical GlovesCut off the fingers of cheap surgical gloves and you have an elastic sleeve to fit lots of different stuff, e.g. your flashlight.
We do this some trick with muzzle loaders when it raining. We put a finger over the barrel and take the wrist and put it over the cap.
sent from Nate's mobile
-
@Etherealicer said:
Key WalletHave a spare key wallet? Take it apart. Its a great source for extra small locking carabiners..
I used to carry one of those, it's all full of cuts and missing pieces of fabric. I don't like the clips very much for holding the keys, they sometimes opened. I'll try them with SAKs, they might work great.

-
OK, I had a problem, I like to carry the full Leatherman Bit Kit. However, it is awkward in my Skinth.
I hardly ever use them, but I WANT to have them if I need them.so I got one of these empty laptop RAM packages.
cut the peg hanger plastic off (It is clear, so hard to see in the picture above.
and it barley fits all the bits (I do not carry the micro bit, since I have one in my Charge.
it is about 4mm thinner than the two bit cards stacked. it is shorter than the bit cards, but it is wider. However, it now fits comfortably in my Skinth!
You will notice that the bits are "standing up" instead of laying down like they do on the cards
I put a piece of electrical tape around it just to make sure it does not come open.
-
How about using rubber bands? From a piece of bycicle tire? You can get that from a repair shop at 0$. Lasts longer, easier to put on/take off.
-
@detron said:
OK, I had a problem, I like to carry the full Leatherman Bit Kit. However, it is awkward in my Skinth.
I hardly ever use them, but I WANT to have them if I need them.so I got one of these empty laptop RAM packages.
it is about 4mm thinner than the two bit cards stacked.
You do like those RAM packeges :D
4mm thinner is quite the achievement.
+1 For rubber bands
-
@pfrsantos said:
How about using rubber bands? From a piece of bycicle tire? You can get that from a repair shop at 0$. Lasts longer, easier to put on/take off.I actually have several "ranger bands" (Inner tube rubber bands) the only problem with those and rubber bands are the friction grip that gets transferred to the sheath.
I am still working the issue, and have a few other closure ideas in mind, but for now I am just happy it fits properly in my Skinth!
-
OK, I had a problem, I like to carry the full Leatherman Bit Kit. However, it is awkward in my Skinth.
I hardly ever use them, but I WANT to have them if I need them.so I got one of these empty laptop RAM packages.
it is about 4mm thinner than the two bit cards stacked.
You do like those RAM packeges :D
4mm thinner is quite the achievement.
+1 For rubber bands
well, you know, use what you've got
-
@dbeeks1 said:
I think the Tec Accessories A-3 glow fob looks pretty cool, but costs more than what I want to spend for something that just looks cool. I made 4 of these for the price of one A-3.I used a cheap 3" plastic line level, v10 glow powder and 30 minute clear epoxy. The glow powder and epoxy are well documented on other forums, but I haven't seen the use of the line level before.
(I also filled the eyes of 10 metal skull beads with the glowing epoxy and still have a small amount of epoxy and glow powder left.)
I was looking for a cheap way to make some of these and found a couple of things at DX. Has anyone tried these? Do they work ok?
Several colours
http://dx.com/p/graffiti-party-diy-glow-in-the-dark-luminous-pigment-270008http://dx.com/p/glow-in-the-dark-silicone-tailcaps-for-flashlights-14mm-green-10-pack-5714

-
I have one of those tailcaps to spare - PM me your address.
-
Thanks for the offer! These are so cheap, you'd spend more in postage than I would if I got some fromm DX.

Just wanted to know if someone had already used the caps or the "paint" and if it really works. I was thinking of filling one of those perfume sample vials with the paint, than get some split ring on the lid to use it in a keychain.

-
I would be afraid of breaking the vial. TZhe paint itself will glow ok - But think about buying some glow pigments, then you can mix it with clear epoxy glue and fill a vial of your choosing.
-
I can always try to find some hollow copper or other material tube with some holes drilled to put the vial inside. That would protect it.
The epoxy glue option you sugest will probably make for a more resistant vial...

-
This link is full of re-use ideas, but all of the results are beautiful knives and such!!!!

-
What a website! So many pretty things, so little discretionary money... ;)
-
I like these Listerine strips but what to do when the container is empty??
Add your favorite flavor Mini Altoid of course :D.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

