Leatherman SIDEKICK / WINGMAN Owners Club
-
-
They did not bow to me, so punishment had to be dealt

-
-
:D

-
Got a wingman and seems like everyone who owns one already notice is the 'wiggle' when it's closed.
This is a simple mod/fix that cost nothing.There are 2 method, temporary and permanent (sorta). Temp will allow you to remove the mod with no tools and permanent will require tools to remove.
Ok, first the temporary mod.
You'll need a PC expansion slot cover, preferably one that doesn't have a chrome coating (because those are too thick)

yours might look different, without the holes, but it shouldn't matter.Tools:
Metal Nibbler (or dremel with cutoff disk or any metal cutting tool)
2 Torx Screwdriver with T10 bit (only needed for permanent version)
optional: metal file or grinding wheel & pliersOk you need to cut this part out of the Expansion slot cover and then cut off the red part.

Depending on how you cut your part, you might need to file/grind down the edges to remove any burrs.With your finish piece you want to insert it under the flathead screwdriver bit.

The curve should butt up against the washer/jointLike so...

When closed the tab should fit under the plastic/box cutter tool. You might have to adjust it so that it'll clear the screw/joint.
This is an outer view on how it should be on the inside.

The only problem with this is that it'll fall out when you use the flathead screwdriver bit. So you might lose it in the field when working with flathead screws. If you like this mod, you can always do the permanent version.
Ok, now to the Permanent version...
You have to remove the Torx screw that are holding the screwdriver bits. You'll need two T10 Torx screwdriver because the bottom one turns when you try to unscrew the top.
Once you have the screw out, take out the screwdriver bits & the washer. You don't need the washer anymore, so store it somewhere safe.Now with the screw driver bit trace the contour on the expansion slot cover. Use the long, lower Torx screw and put it in the holes to line them up.

Now cut it out and file/grind the edges.

Now reassemble your bits. Tab on the bottom, Flathead screwdriver & Phillips driver.

Afterwards open your screwdriver bits. if they're hard to open, loosen the torx with half a turn until the bits can turn freely.Again the tab should fit under the plastic/box cutter when you close it. (not fully closed in pic)

if you still get a minor 'wiggle' use a pair of pliers and bend the tab up slightly. This way it'll make better contact with the plastic/box cutter. Some expansion slot covers already has a slight bend on it so depends on what kind you have, you may or may not have to adjust.Here's the Wingman opened, the tab doesn't stick out that much to get in the way of anything.

Temp version took me about 15mins, permanent version took about 30mins. The metal nibbler made cutting the parts out fast and used a dremel grinding stone to remove the burrs. Depending on what you use, it might take you longer or shorter, but still relatively easy to do.
Technically you can use the wingman's plier to bend and break off the expansion slot cover and the file to smooth it. It won't look as nice, but it'll still work and cost you nothing if you have no other tools.
-
Thanks for the instructions dilldoe
I use the lanyard ring on my Sidekick for this same purpose. Not sure why the Wingman doesn't come equipped with a lanyard ring though 
-
Cool ideas
I've got use to wiggle as owned a wave for years plus a surge and find they all have a little play,infact my sidekick is the least wiggly :D -
Brand new Sidekick and Croc combo owner.
Sent from my not yet outdated Galaxy Note 2 via Tapatalk!
-
I was just remarking in another thread how well the clam shell opener worked for me today. It saved me from painfully using scissors and still not getting the package opened adequately.
-
@sawman said:
I was just remarking in another thread how well the clam shell opener worked for me today. It saved me from painfully using scissors and still not getting the package opened adequately.That thing is pretty sharp, and convenient for that frustrating type of packaging. I think the small serrated blade on the Sidekick would be good for that as well. I guess I'll likely get to test that out on Christmas, unless I decide to carry the Wingman that day just to use the package opener...that would make sense after all ;)
-
Nah, we all know how well the package opener works. You need to test how well the small serrated blade works. Dammit, man... this is SCIENCE! :D
-
@Lynn LeFey said:
Nah, we all know how well the package opener works. You need to test how well the small serrated blade works. Dammit, man... this is SCIENCE! :DWell, in the interest of science and the love of testing our multitool implements, I will carry the Sidekick in case there are any clamshell packages to open :D
-
I was just remarking in another thread how well the clam shell opener worked for me today. It saved me from painfully using scissors and still not getting the package opened adequately.
That thing is pretty sharp, and convenient for that frustrating type of packaging. I think the small serrated blade on the Sidekick would be good for that as well. I guess I'll likely get to test that out on Christmas, unless I decide to carry the Wingman that day just to use the package opener...that would make sense after all ;)
I really don't like open that bit. weary of slicing open my thumb trying to rotate it out with all the other bits (can opener & file) stuck to it. or is there a special, secret way of just opening one bit at a time?
-
I was just remarking in another thread how well the clam shell opener worked for me today. It saved me from painfully using scissors and still not getting the package opened adequately.
That thing is pretty sharp, and convenient for that frustrating type of packaging. I think the small serrated blade on the Sidekick would be good for that as well. I guess I'll likely get to test that out on Christmas, unless I decide to carry the Wingman that day just to use the package opener...that would make sense after all ;)
I really don't like open that bit. weary of slicing open my thumb trying to rotate it out with all the other bits (can opener & file) stuck to it. or is there a special, secret way of just opening one bit at a time?
There's no special way as far as I know. I have that same worry as well, and even moreso with the serrated blade in that same spot in the Sidekick. Hasn't been a problem for me yet, but it's something to be watchful of.
@Lynn LeFey said:
Nah, we all know how well the package opener works. You need to test how well the small serrated blade works. Dammit, man... this is SCIENCE! :D
I don't, which is another great reason I need to get me a Wingman!
Yes, Derek, yes it is
>:D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



