new wave...
-
I hope this is true. If they make any change, I hope an awl gets added as well.
-
I don't think it will happen next year. The Rebar has only been out for roughly a year and a half, and adding replaceable cutters to the Wave would cannibalize Rebar sales. I would guess that the Rebar is still selling fairly well (especially with people around here buying them up for mods
), so it wouldn't be a good business decision for them to add the replaceable cutters to the Wave this soon.There were similar discussions about the ST300/Surge, and if you look at the Leatherman timeline, the ST300 had been out for 4 years before they released the new Surge.
My guess is that they'll hold off on updating the Wave/Charge line until Rebar sales start to slump, so we won't see a Wave/Charge with replaceable cutters until 2015 or 2016.
of course, I certainly wouldn't mind being wrong on this one... :D
-
@Breezy12 said:
I don't think it will happen next year. The Rebar has only been out for roughly a year and a half, and adding replaceable cutters to the Wave would cannibalize Rebar sales. I would guess that the Rebar is still selling fairly well (especially with people around here buying them up for mods
), so it wouldn't be a good business decision for them to add the replaceable cutters to the Wave this soon.There were similar discussions about the ST300/Surge, and if you look at the Leatherman timeline, the ST300 had been out for 4 years before they released the new Surge.
My guess is that they'll hold off on updating the Wave/Charge line until Rebar sales start to slump, so we won't see a Wave/Charge with replaceable cutters until 2015 or 2016.
of course, I certainly wouldn't mind being wrong on this one... :D
sound points. the only factor I see that leads to a different view is that Wave sales are much higher than Surge sales. not sure if that would alter the timeline, but a valid point to make
-
There is the small factor that producing a Wave with the Rebar pliers would mean they only had to produce one set of pliers and that should cut the cost of the Rebar slightly.
-
That would be sweet if they put Rebar pliers on the Wave
-
I don't think it will happen next year. The Rebar has only been out for roughly a year and a half, and adding replaceable cutters to the Wave would cannibalize Rebar sales. I would guess that the Rebar is still selling fairly well (especially with people around here buying them up for mods
), so it wouldn't be a good business decision for them to add the replaceable cutters to the Wave this soon.There were similar discussions about the ST300/Surge, and if you look at the Leatherman timeline, the ST300 had been out for 4 years before they released the new Surge.
My guess is that they'll hold off on updating the Wave/Charge line until Rebar sales start to slump, so we won't see a Wave/Charge with replaceable cutters until 2015 or 2016.
of course, I certainly wouldn't mind being wrong on this one... :D
sound points. the only factor I see that leads to a different view is that Wave sales are much higher than Surge sales. not sure if that would alter the timeline, but a valid point to make
good point, detron. LM has stated that the Wave is their top selling tool of all time by a large margin. if Wave sales have started to decline, then this would be a great way to revive them (albeit at the expense of Rebar sales). I'm guessing the margins are higher on a Wave as well.
@Cupboard said:
There is the small factor that producing a Wave with the Rebar pliers would mean they only had to produce one set of pliers and that should cut the cost of the Rebar slightly.another good point, but keep in mind that LM has been producing the current Wave/Charge pliers for years, so it's not like they need to invest in new manufacturing equipment. OTOH, maintenance costs on the existing equipment could play a factor. They'll want to phase out those plier heads eventually; I guess it's just a question of balancing costs and sales and profit margins and...
??? 
this is just one of the reasons I'm an engineer and not a businessman. :D
-
To my eye, and I'm not a machinist, the Wave pliers look like they might need a bit more work to do than the Rebar ones.
You have to cast them and then grind down the pliers in an even way all round but all the Rebar ones require is a hole drilled and tapped. Then you've got the added cost of the wire cutter, but it is actually added cost? I don't know. I'll shut up now.
-
@Cupboard said:
To my eye, and I'm not a machinist, the Wave pliers look like they might need a bit more work to do than the Rebar ones.You have to cast them and then grind down the pliers in an even way all round but all the Rebar ones require is a hole drilled and tapped. Then you've got the added cost of the wire cutter, but it is actually added cost? I don't know. I'll shut up now.
I think you're right about the Wave pliers requiring a bit more work. The grinding is all automated, with a cool looking robotic arm moving the plier heads around, but it's definitely an added step that takes time and money.
The replaceable wire cutters are laser-cut using the same machine that laser-cuts all of LM's premium steel blades (both 154CM and S30V), so I think the only added cost to the plier head would be the cost of the extra 154CM steel. And the replaceable cutters are attached to the plier head manually... but I have no idea how you would factor that into the cost.
yes, I have taken the LM factory tour twice. :D
-
just a though...
how "easy" is adding a rebar head to a Wave? I ask, because I to do think that slimming down the plier heads save some cost, but only if the head is a direct swap?
if not, they would still need to adapt the machinery or change the design of the Rebar to fit the new Wave Head.
-
@El Rago said:
just a though...how "easy" is adding a rebar head to a Wave? I ask, because I to do think that slimming down the plier heads save some cost, but only if the head is a direct swap?
if not, they would still need to adapt the machinery or change the design of the Rebar to fit the new Wave Head.
If you look in the mod squad forum, you'll see
The only thing that doesn't "fit" is that the plier head and the handle of the scissors close "in the same place", so they're a bit in the way for each other. That should be a simple design change.
-
I really hope they don't put the Rebar plier head on the Wave... The plier head on the Wave/Charge is, in my opinion, the best one they've made so far. The wire cutters work very well, and the bolt gripper area on that head is better than the Rebar.
I've found that the issue with the Rebar's head is that they used the wire cutters from the larger ST300 head and that encroaches on the rest of the pliers. They don't grip as well as the Wave/Charge head, and they don't grip as well as the ST300 head which is large enough to accommodate them.
Not to mention the teeth on the needle-nose plier portion is far too coarse and mars up a fastener more easily than the finer grain teeth on the current Wave/Charge head.
The cutters are great, but it ends up being that you get a subpar plier for the sake of replaceable cutters. If they put that plier head on the Wave or Charge, I'll have to pick up a few more of the current model to cover me for a while, because I don't want to use that plier head regularly. On a $30 Rebar, sure. Not on my $80 Charge.
-
+1 on everything the drummer boy said. :D
I've said it a couple of times as well, I simply prefer the old head better and really hope they don't change it.

-
It's a bit of a Marmite issue really - I for one love the Rebar head and it works much better for me.
-
I know I've brought this up before, but my memory isn't what it was

"are the replaceable cutters on the ST300 the same as the Rebar ones ?"
ie. do they only make one type/size ? -
@Taxi Dad said:
I know I've brought this up before, but my memory isn't what it was
Yes :P
@Taxi Dad said:
"are the replaceable cutters on the ST300 the same as the Rebar ones ?"Yes :)
@Taxi Dad said:
ie. do they only make one type/size ?No, so you can be forgiven for getting in a muddle. They're all the same size but there's a special EOD version that doesn't have the notch in the bottom.
-
thanks Tom

wonderful explanation
point me towards this thread next time I ask :ahhh -
;)
It's not just you, I'm as bad as anyone.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login