mod advice needed
-
@Syph007 said:
So essentially you want to have 2 blade layers. The only issue is the backtool on a blade layer is usually the corkscrew which is wider than the layer itself. If you stuck an awl in there on the inside layer instead of a second corkscrew I dont see why it wouldnt work. ** The nail nick from the inner blade layer will block the nail nick of the outside layer as well**, but there might be enough room between the layers to get a nail in there.Maybe you could reverse the inner blade, so it's like the scissors on most SAK's? Or doesn't it work so easily?
-
@Syph007 said:
So essentially you want to have 2 blade layers. The only issue is the backtool on a blade layer is usually the corkscrew which is wider than the layer itself. If you stuck an awl in there on the inside layer instead of a second corkscrew I dont see why it wouldnt work. The nail nick from the inner blade layer will block the nail nick of the outside layer as well, but there might be enough room between the layers to get a nail in there.I think about remove saw from huntsman and place there serrated large blade. Opening in same way like it was before with saw. Hm my english

-
So essentially you want to have 2 blade layers. The only issue is the backtool on a blade layer is usually the corkscrew which is wider than the layer itself. If you stuck an awl in there on the inside layer instead of a second corkscrew I dont see why it wouldnt work. ** The nail nick from the inner blade layer will block the nail nick of the outside layer as well**, but there might be enough room between the layers to get a nail in there.
Maybe you could reverse the inner blade, so it's like the scissors on most SAK's? Or doesn't it work so easily?
Yes this is my dream picnic SAK :D
-
So essentially you want to have 2 blade layers. The only issue is the backtool on a blade layer is usually the corkscrew which is wider than the layer itself. If you stuck an awl in there on the inside layer instead of a second corkscrew I dont see why it wouldnt work. ** The nail nick from the inner blade layer will block the nail nick of the outside layer as well**, but there might be enough room between the layers to get a nail in there.
Maybe you could reverse the inner blade, so it's like the scissors on most SAK's? Or doesn't it work so easily?
Nope that works on the 93 since they are symmetrical, but the 91mm wont work that way due to the backlayer tools, the knife only fits one way. Pretty much on 91mm mods you are limited to rearranging layers, not creating new ones from existing tools, the springs are too highly specific.
-
So essentially you want to have 2 blade layers. The only issue is the backtool on a blade layer is usually the corkscrew which is wider than the layer itself. If you stuck an awl in there on the inside layer instead of a second corkscrew I dont see why it wouldnt work. ** The nail nick from the inner blade layer will block the nail nick of the outside layer as well**, but there might be enough room between the layers to get a nail in there.
Maybe you could reverse the inner blade, so it's like the scissors on most SAK's? Or doesn't it work so easily?
Nope that works on the 93 since they are symmetrical, but the 91mm wont work that way due to the backlayer tools, the knife only fits one way. Pretty much on 91mm mods you are limited to rearranging layers, not creating new ones from existing tools, the springs are too highly specific.
I can live without one back tool in that layer? What back tool is there?
-
The only one that would fit I think is the awl. Its too thin I use a little washer, but it would be ok without it if you didnt feel like making a tiny one. There are the chisel and fine driver from the swiss champs but those are even thinner and for sure need a washer. The only one I used before though was an awl in place of corkscrew. It means you have 2 awls, but thats the easiest option. And 2 small blades too.
The only config I can think of that didnt double up tools would be to add in a combo tools.
- combo tool / main blade / corkscrew back tool
- small blade / serrated main / awl back tool
- scissors layer
Might be better to have the scissors in the middle too... dunno.
-
OMG idea: grind wood saw to form of the serrated blade

-
@Syph007 said:
The only one that would fit I think is the awl. Its too thin I use a little washer, but it would be ok without it if you didnt feel like making a tiny one. There are the chisel and fine driver from the swiss champs but those are even thinner and for sure need a washer. The only one I used before though was an awl in place of corkscrew. It means you have 2 awls, but thats the easiest option. And 2 small blades too.The only config I can think of that didnt double up tools would be to add in a combo tools.
- combo tool / main blade / corkscrew back tool
- small blade / serrated main / awl back tool
- scissors layer
Might be better to have the scissors in the middle too... dunno.
This config is much better. corkscrew is must have for one dream picnicker SAK.
-
Or you could try finding a Wenger Double Blade. :whistle:
:D
I like the mod idea by Syph007. :cheers:
-
Ah that looks great Peter. As I thought putting something in between the 2 blade layers seems to be the best idea.

-
Yes, having the scissors there means you can get at all four nail nicks on the blade layers easily.
I did try the blade layers side by side but it was just too crowded.
There is a little bit of filework/jimping on the spine of the serrated blade to help with identification. -
Mh...can you flip the tools on a 91mm blade spring that easily?
Or did you mod the spring in some way? -
The spring wasn't modded. I can't remember what spring I used though. Plus I had to shim the backside awl with a washer to get to the correct thickness.
-
-
Samek did something nice. Roll down the page. http://forum.multitool.org/the-mod-squad/brass-spartan/
Or could you fit solo knife layer or backspring there? Maybe a nailfile instead of small blade?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


