And so it begins.... (My adventures into Alox!)
-
I havent been posting every single alox custom in this thread since so many are just the same model. This one I put a bit of extra effort in though so I wanted to show it off. I normally make round washers to use as spacers for the phillips driver in the triple tool layer I make, but I wanted to make spacers that match the contour of the liners to make it all blend in.
I think it turned out so nice. Those spacers are riveted to the liners so they will never rotate or move. Both red and brass and black and brass are my favorite combinations of all time. :D







-

I like it very much.
Only a bit related: Do you know if the triple tool layer will work in 91 mm, too?
-
-
ANODIZER! Imma get me some purple scales. ;)
-
That one's a beauty Syph

-
Beautiful job Syph!
JR -
Ha! Yes I know you've always wanted purple and purple on Ti is one of the good colors too! :D
Its too cold here to setup my Ti anodize right now, but Im going to get a heater for my shop. You know its cold when you go to dunk a hot part off the grinder in your quench bucket and its frozen!
-
I keep saying this, but I'm going to figure out another custom. I just gotta get me some of that Red and brass love.

-




Robert is too modest with his "not posting every mod due to same models.." I believe I speak for all of us when I say we want to see every single one. This may be my most checked thread.
The above example of his amazing work is on its way to me. I cannot wait to have it in hand. I have dubbed it "Vader" for the time being, as I think it would look quite at home among a gaggle of his "Stormtrooper" models. Still, I wouldn't mind a more SAK-like proper name if anyone has one.
Well done, Syph007!
Now, please go back to posting all of them! I need my fix.
-
@glorn said:
Robert is too modest with his "not posting every mod due to same models.." I believe I speak for all of us when I say we want to see every single one. This may be my most checked thread.The above example of his amazing work is on its way to me. I cannot wait to have it in hand. I have dubbed it "Vader" for the time being, as I think it would look quite at home among a gaggle of his "Stormtrooper" models. Still, I wouldn't mind a more SAK-like proper name if anyone has one.
Well done, Syph007!
Now, please go back to posting all of them! I need my fix.
glorn,
I have no doubt your anticipation is well founded.
Syph007 makes exception pieces.
Totally agree with your sentiment that Syph007 should post every build, irrespective of repetition or otherwise, as it would be appreciated by those that follow this thread. -
That's a nice one Glorn:). Nice work by Syph as usual:D
Sent from my XT901 using Tapatalk
-
I got this beauty done last night. I think this is my new favorite version of a 3 layer alox mod and here is why. I dont need the can opener or little scrwdriver at the tip. Knife blade tip works for small screws and if I need to open a can I can make do with the knife blade, reamer, or cap lifter.
So... replacing the can opener with a phillips driver makes sense for me, and anyone else who doesnt need a can opener. Now the problem with replacing it directly and leaving the opener layer on the outer layer is the phillips driver will hit and chip the scale since its head is wider than the layer itself.
So... without the can opener, we can move that layer to the center which gives the phillips head lots of room and nothing gets hit. The second benefit is that both drivers are now centered in the SAK and feel more natural in use.
All nail nicks work perfect and the overall package is a pleasure to use and carry since it is of minimal thickness! :D Now I need a name for this model. Urban phillips pioneer, but better. :D







Cheers!
-
Very nice setup syph! Love it! JR
-
That was a good idea, and great execution Syph8)
Sent from my XT901 using Tapatalk
-
Really like that one Syph, especially because it is a 3 layer with phillips!
Great job mate!! It's a real beauty

-
Love that Symph!
Tell me, could that have a lanyard ring added and the reamer replaced with a small blade or the small nail file?
Regards, Jon
-
@JDO330 said:
Love that Symph!Tell me, could that have a lanyard ring added and the reamer replaced with a small blade or the small nail file?
Regards, Jon
I'm not Syph, but I'm sure that's a possibility. Keyring or no keyring is always an option, and I'm quite sure the small blade shouldn't be a problem as well ;)
-
Small blade is a direct swap in, it just needs a tiny washer. The nail file from a cadet needs a new spring with thicker rest to work properely (so it costs more) but does work.
-
Oh baby, I was restocking on screws and found that knifekits has Ti screws now... 2 buck each but I gotta get some for Ti urban pioneer builds... :D
They are a shallow socket style so they will still fit flush with the scales too. mmmm... They can be anodized too!

http://www.knifekits.com/vcom/product_info.php?products_id=4723
-
So Syph, what is the likelihood of you producing something like this one day? Cause I would go broke if you did lol


Edit: Nevermind, I see the answer to my second question!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login