Show off your Sak mod's!
-
Beautiful! Exposed rivets are cool. ;)
-
Thx @all. I like exposed rivets too. Using them, custom plus scales are easier to make and the knife still can be taken apart. That was a great benefit working on this mod.
However, 84 mm long nail file is a pain in the a-s-s ... the fourth pin is split inside and building up the long nail file-layer is fricking... ;-)
-
Last mod, the "Wenger Mender", something I never understood why was not in Wenger's catalog.
Quick description: a Toolchest Plus without fishscaler, compass and magnifier. My idea of a nice Wenger Champ.

Tools.

Comparison with Swisschamp.

Excuse the bad pictures! I just finisehd it now.
-
Looks like a really useful package and well done, thought I would have probably reversed the layers a bit. :P
Phillips/wrench in the middle, then pliers, scissors, blade.
It looks to me as if the scissors nail nick could be hidden by the phillips here making them harder to open.
-
@enki_ck said:
Looks like a really useful package and well done, thought I would have probably reversed the layers a bit. :PPhillips/wrench in the middle, then pliers, scissors, blade.
It looks to me as if the scissors nail nick could be hidden by the phillips here making them harder to open.
I just respected the factory configuration and added the two saws at the end. Scissors are more or less fine, much better than some factory models with it beside locking blade, that's really annoying sometimes, with the nail nick covered by the unlocking leverage.
I was thinking in changing the order, specially to put the wrench closest as possible to one side, not in the middle; but at the end I decided to not change it, because that makes confortable to tight screws, but not to loosen it, or viceversa.
We are insane. :D :D

-
Looks like a really useful package and well done, thought I would have probably reversed the layers a bit. :P
Phillips/wrench in the middle, then pliers, scissors, blade.
It looks to me as if the scissors nail nick could be hidden by the phillips here making them harder to open.
I just respected the factory configuration and added the two saws at the end. Scissors are more or less fine, much better than some factory models with it beside locking blade, that's really annoying sometimes, with the nail nick covered by the unlocking leverage.
I was thinking in changing the order, specially to put the wrench closest as possible to one side, not in the middle; but at the end I decided to not change it, because that makes confortable to tight screws, but not to loosen it, or viceversa.
We are insane. :D :D

I see a lot of merit in having the Philips/Wrench offset from the center of the knife as much as possible. That way the wrench can get on to more nuts that are close to a flat surface.
Makes the Phillips less wieldy though, I admit.
I actually saw a Wenger today with almost that exact same tool load as your mod. I was tempted, but then I already have too many Vics and Wengers (don't we all?) ;) -
@neillcurrie said:
... but then I already have(too)many Vics and Wengers (don't we all?) ;)Many? ... Maybe.
Too many? NEVER! 

-
@neillcurrie said:
I see a lot of merit in having the Philips/Wrench offset from the center of the knife as much as possible. That way the wrench can get on to more nuts that are close to a flat surface.
Makes the Phillips less wieldy though, I admit.I actually saw a Wenger today with almost that exact same tool load as your mod. I was tempted, but then I already have too many Vics and Wengers (don't we all?) ;)
Yes!, that was my thought. I have a Wenger Biker (nice SAK!) in my MTB and that's my experience: not confortable on flat surfaces. But I thought that, because you have to reverse the tool depending on tightening or loosing, I should adopted a compromise leaving it in the middle (I supose that's the idea of Wenger). If I leave it close to one side, it's going to be very good for tightening, but bad for the opposite task. You can work with the wrench a bit crossed anyway, so I think it's a position where is going to work for all scenarios. Not perfect, but kind of universal.
This is my reflection, but maybe I'm just overthinking it. Ah... I remember the old days, when I simply used the SAKs...

-
Did this one last night...

Replaced the red plastic scales on this old Victorinox Classic with some hardwood from an incense burner.
Need to fit a new spring to the scissors and add a keyring, just a simple leather lace lanyard for now. -

Pioneer with scissors
Stonewash Tools
Black G10 liners and spacer
Black Hardware
My first run of Hard Ano scalesMINE!!! There may be other alox but this one is MINE!
-
Nice shade of Blue!
-
NICE! And yes nice shade of blue
JR -
That's a beauty Rick

-

Added my 91mm awl to a rambler. Just doubled ip the blade and file.
-
finished a farmer for ppratt. Standard config with stonewash.

-
SORRY! I boxed it up for shipment before I snapped a closed photo. I will get a shot of the next one closed.
-
Found a very old (1940's???) Vic all beaten and abused in the TSA resale bin. Decided to turn it into a functional vintage edc knife. As it's difficult to find exact period replacement parts for the corkscrew, large and small blades, and scissors, I went with what I had on hand: a Wenger corkscrew, and contemporary 91mm Vic scissors. As the scissor backspring was broken too, I swapped the spring for the saw to the scissors, reground the profile of the handle end of the spring, and made a custom brass spacer as the spring wasn't thick enough. The small blade I turned into a flat Phillips driver, similar to that on some Wengers. The Large blade reprofiled nicely, it's hard to really tell it's now about 1/4 inch shorter than originallly.
The scales were very difficult to remove without slightly damaging the rivet holes. I filled the damage with JB weld, and that it mostly hidden by the mushroom heads of the rivets.
A general tidy up, some tlc, other general tool renovation and cleaning, and finally a good polish. Possibly the most fiddly job was the final one: grinding/sanding down a modern Vic toothpick and tweezers to fit the skinny slots on the '40's knife.
I still have to secure one edge of the Vic shield, which is lifting slightly from the scale......any ideas about what adhesive to use, and how best to do it??
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login