SwissFlame - no fire
-
Registered under ebay.de for my german language purpose, having an USA address for the shipment.


-
Anybody need swissflame?
-
Blue SwissFlame and red CampFlame. Both worked until they ran out of fuel.
-
Guess I'll just have to live with the collectors-item-value and forget about the flame.
-
-
@nate j said:
Guess I'll just have to live with the collectors-item-value and forget about the flame.
I'd be willing to do a straight up trade for a Climber Plus and a Bic lighter, if that would make you feel better. I'll even through in one free replacement for the Bic... >:D :D
Thanks for the kind offer ... but i'll have to decline :D
-
What causes these lighters to die? Can they be disassembled and repaired? I know how the coast lighter knives fail (the ones that are a copy of the Wenger handyman) - a brittle nylon fuel tank cracks with age. But it sounds like the Swiss flame still holds butane, but doesn’t fire? That sounds like something fixable, if you can get to the innards.
Charles.
-
The nozzles are made way too precise, causing dirt particles in natural gas to clutter the nozzle.
I've read one day that someone managed to repair the lighter by putting it in an ultrasonic cleaner. It did, however, cause the gaskets to leak. So the lighter didn't hold gas in it's tank for more than a few minutes and was therefore just as useless as before.
-
The gaskets should just be little o-rings. Are they all accessible? Can it be disassembled?
Charles.
-
Not as far as I know

-
@ChopperCharles said:
The gaskets should just be little o-rings. Are they all accessible? Can it be disassembled?Charles.
Fundamentally, the problem is a design flaw, not a maintenance issue.
-
@burnside said:
I wonder if anyone has ever come up with a fix for the SwissFlame?
Spent a good part of an evening striping one. Initially thought the jet was blocked but turned out the valve inside the reservoir was stuck. Got it free but I’d already damaged the jet hole thinking it was blocked so gas was now releasing but not successfully lighting on piezo. Found a replacement donor jet from another no name jet lighter but managed to crack the ceramic shield so whole restore effort was abandoned. I can’t recommend trying a fix these unless you get access to a few and can cannibalizes parts. >:(


-
Wow fascinating! I've wanted to get mine to work but didn't want to take it apart. Thanks for giving it a try and giving us a glimpse of the inerds.
-
Sadly, even when the SwissFlame works, it has a great deal of trouble in cold weather....exactly when you would need it the most.
-
I had a working one. Sold it to another MTo member for about E 65. Don´t know its current status.
-
For those interested, here’s a description of how it works:
Pressing the thumb press exposes the burner while rocking a lever that pulls up the reservoir valve, releasing the butane that vaporizes in the tube below the jet that dog-legs around the back tool pivot.
At the same time, the thumb press loads the piezo spring, that trips at the bottom of the press, striking a small crystal that generates a short pulse of electricity of several hundred volts, enough to jump an air gap at the burner created by a small insulated wire that runs up from base of the piezo generator, grounding back to the piezo via the base of the burner.
The jet is a tiny hole finer than the tip of a needle, punched in a thin metal disk. The shape and size of this hole is critical as it must direct the escaping gas vertically up the burner tube to mix with air, ignited by the spark, creating the characteristic jet flame. Any contamination of this jet can upset this delicate setup, and trying to clear the hole with a pin or needle will only distort the hole, causing a misaligned flame or a complete failure of the burner to light.
Releasing the thumb lever closes the reservoir valve and the flame goes out, returning the lighter’s cover cap.
The flame strength is a function of the gas flow, regulated by a screw that surrounds the refilling value. This screw compresses a semi-permeable fiber washer inside the value, allowing controlled adjustment of the flow rate.
The burner/jet, piezo generator and reservoir value are all off-the-shelf components common to many jet-style burners. The plastic reservoir, metal thumb lever/cap and metal sleeve that slides over the whole lighter (creating the ‘tool’ layer) are custom-built components.
Filling the reservoir is done by inverting the lighter so that a pressurized butane canister can be press-fitted to the filling valve to dispense butane fluid (based on the canister having a higher pressure than the reservoir). A window in the reservoir shows the butane level (rather small capacity).
There are several design weaknesses, such as the sticking reservoir value (an internal brass rod inside the valve that I think is meant to be an invert cut-off safety), as shown in my 2nd picture above. The burner/jet combination appears sub-optimized, hence the lighting difficulty in some conditions. The wire from the piezo is just insulated at the top with a dip-coating (which can wear off causing a short and failure of the spark). And the butane reservoir is very small.
A bit of a waffle, but hopefully of some interest? :D
-
I see why the Idea was abandoned. Might as well just fit a mini Bic in a fat rear scale then. Hmm I wonder how rediculous that would look
-
That´s been done. Kind of.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

