And so it begins.... (My adventures into Alox!)
-
Syph, that is awesome! Can you quote me for one please.
Sent using my chubby fingers...
-
I was low on farmers so I grabbed a bunch lately for teardowns. I forgot farmers are nicer to rip apart, you only need to drill out 2 pins and the 3rd you can cut with side cutters. This works since the saw backspring falls out after you remove 2 pin.
So it's 33% less work to take apart alox farmers for donors.












-
And 33% less likely to mess up the scales. :D That's a good tip.

-
Here's a mod Ive had on the bench for awhile, that has stalled a bit and I need to figure out a solution.
The goal was to get a scalpel blade holder on a SAK... I cut down one and made a pivot and it fits and works well, the problem is i needs to sit far down to keep the sharp blade hidden, but there is no way to pull it out. All I can think of is to graft or bolt on some metal and form a nail nick on that... but I keep trying to think of an elegant solution.




-
@Syph007 said:
Here's a mod Ive had on the bench for awhile, that has stalled a bit and I need to figure out a solution.The goal was to get a scalpel blade holder on a SAK... I cut down one and made a pivot and it fits and works well, the problem is i needs to sit far down to keep the sharp blade hidden, but there is no way to pull it out. All I can think of is to graft or bolt on some metal and form a nail nick on that... but I keep trying to think of an elegant solution.

The first pic was barely loaded and I knew this would be pure awesomeness!!!!
Thanks Syph for all your moding greatness. It just made my day!!!
p.s. could you make a blade holder, from scratch, with a nail nick like the ones on the drivers of a LM Juice?
-
Here's a mod Ive had on the bench for awhile, that has stalled a bit and I need to figure out a solution.
The goal was to get a scalpel blade holder on a SAK... I cut down one and made a pivot and it fits and works well, the problem is i needs to sit far down to keep the sharp blade hidden, but there is no way to pull it out. All I can think of is to graft or bolt on some metal and form a nail nick on that... but I keep trying to think of an elegant solution.

The first pic was barely loaded and I knew this would be pure awesomeness!!!!
Thanks Syph for all your moding greatness. It just made my day!!!
p.s. could you make a blade holder, from scratch, with a nail nick like the ones on the drivers of a LM Juice?
+1

How about a flipper?
-
Here's a mod Ive had on the bench for awhile, that has stalled a bit and I need to figure out a solution.
The goal was to get a scalpel blade holder on a SAK... I cut down one and made a pivot and it fits and works well, the problem is i needs to sit far down to keep the sharp blade hidden, but there is no way to pull it out. All I can think of is to graft or bolt on some metal and form a nail nick on that... but I keep trying to think of an elegant solution.

The first pic was barely loaded and I knew this would be pure awesomeness!!!!
Thanks Syph for all your moding greatness. It just made my day!!!
p.s. could you make a blade holder, from scratch, with a nail nick like the ones on the drivers of a LM Juice?
+1

How about a flipper?
Ya that would be the easiest I think, and probably safest way to open a very sharp tool like this. The only problem is that is has to stick up high enough so that when in open mode it clears the backspring.
The customer that wanted this sent me 2 holders just in case I messed one up, so I have a spare if I mess up completely. This build will be very unique for sure though, its got alot of specific tools in one custom SAK that is for a very specific task which is picture framing. It has a serrated small blade on there too.
-
@Syph007 said:
Ya that would be the easiest I think, and probably safest way to open a very sharp tool like this. The only problem is that is has to stick up high enough so that when in open mode it clears the backspring.The customer that wanted this sent me 2 holders just in case I messed one up, so I have a spare if I mess up completely. This build will be very unique for sure though, its got alot of specific tools in one custom SAK that is for a very specific task which is picture framing. It has a serrated small blade on there too.
Indeed, if not high enough it would just hit the backspring and it wouldn't open...
Depending on the position of the tool, wouldn't it be possible for you to make a cutout on the handles to facilitate the access to a nail nick?
BTW, I thought you were just experimenting.
-
A nice brass and black one today. I wish more people wanted the metal saws, I think they are very handy on a SAK and also I have a pile of them. :D





-
She's a beauty Syph! JR
-
The brass liners are a nice touch 8)
-
Not sure if WWW meant this but would a, dare I say this here ... lol, a Leatherman eg Charge type solution work ie a transverse nodule or knick towards the pivot on the tools body suffice? More specifically like the bit holder tool, or flat screwdriver, scissors etc.

-
@Syph007 said:
Here's a mod Ive had on the bench for awhile, that has stalled a bit and I need to figure out a solution.The goal was to get a scalpel blade holder on a SAK... I cut down one and made a pivot and it fits and works well, the problem is i needs to sit far down to keep the sharp blade hidden, but there is no way to pull it out. All I can think of is to graft or bolt on some metal and form a nail nick on that... but I keep trying to think of an elegant solution.




How about a thumb stud? You could cut a little notch out of a scale before ano and then that would work. It would also aid in keeping better hold of the blade ;)
Sent from my iPhone using Tapatalk
-
Oh btw still waiting on those 91 Alox scales :P
Sent from my iPhone using Tapatalk
-
@Heywood Floyd said:
Not sure if WWW meant this but would a, dare I say this here ... lol, a Leatherman eg Charge type solution work ie a transverse nodule or knick towards the pivot on the tools body suffice? More specifically like the bit holder tool, or flat screwdriver, scissors etc.

That is exactly what I meant!! I was also surfing through a Juice related thread so it came to mind immediately.
BTW that is a beautiful piece of Charge!!
-
@Heywood Floyd said:
Not sure if WWW meant this but would a, dare I say this here ... lol, a Leatherman eg Charge type solution work ie a transverse nodule or knick towards the pivot on the tools body suffice? More specifically like the bit holder tool, or flat screwdriver, scissors etc.

That is exactly what I meant!! I was also surfing through a Juice related thread so it came to mind immediately.
BTW that is a beautiful piece of Charge!!
That does have a rugged looking appeal to it eh... :D
-
@Heywood Floyd said:
Not sure if WWW meant this but would a, dare I say this here ... lol, a Leatherman eg Charge type solution work ie a transverse nodule or knick towards the pivot on the tools body suffice? More specifically like the bit holder tool, or flat screwdriver, scissors etc.
That is exactly what I meant!! I was also surfing through a Juice related thread so it came to mind immediately.
BTW that is a beautiful piece of Charge!!
That does have a rugged looking appeal to it eh... :D
Thanks for the kind words gents. It is a very easy mod. Essentially undo fasteners, re-arrange some tools and voila. Very unlike the skill, problem solving and patience amongst other qualities needed to make Syp007 type mods.
It does have some nice qualities that come along with the turf, like detachable pocket clip, frame locking CPM S-30V blade and the ability to easily changeout the tool sets from those remaining.
Its pretty compact but I've not found any useful solution for the ex plier head pivot space.
Syp007 please do tell us the solution you end up settling on to open the blade carrier.
Thanks also for your continued efforts in sharing the SAK modding journey. -
Dug out some 0.050" Ti today...



Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
>:D