Is there an adapter that will fit the Cybertool bit adapter for using 1/4 bits?
-
I haven't found a good 4mm hex bit to 1/4" hex bit adapter yet, but here is a nice 4mm hex to 1/4" drive:
http://chadstoolbox.com/05050010001wera8700adaptor14hexx4mmsq.aspx
Still looking...
-
@NutSAK said:
I haven't found a good 4mm hex bit to 1/4" hex bit adapter yet, but here is a nice 4mm hex to 1/4" drive:http://chadstoolbox.com/05050010001wera8700adaptor14hexx4mmsq.aspx
Still looking...
Thanks for the link! I will check it out!
Just a thought but does anyone make a full/bigger 4mm hex kit with alot more bit choices that will fit the CT?
-
I've never seen one mike.
I did some looking.
good luck
-
Mini bit kits are out there. you can get cheap ones or name brands.
-
I was curious but rethinking this as I would have to wonder how much torque the 4mm CT would be able to take before breakage/damage if used hard. Especially compared to just using a 1/4 socket setup.
I was just thinking of a more complete kit that I could have when I carried my CT34 in my backpack.
Thx. :D
-
-
@sir_mike said:
I was curious but rethinking this as I would have to wonder how much torque the 4mm CT would be able to take before breakage/damage if used hard. Especially compared to just using a 1/4 socket setup.I was just thinking of a more complete kit that I could have when I carried my CT34 in my backpack.
Thx. :D
The driver itself can take quit a bit of torque. I have bent and broke a couple of the bits way before i even stressed the driver.
-
@Etherealicer said:
Found one ;)I don't think that will work. That is a 1/4" drive socket with 4mm hex. What Mike wants is a 4mm male bit on one end, and a 1/4" female hex on the other, to put 1/4" bits in. I've seen many the other way around to adapt 1/4" hex to 4mm, but not to adapt 4mm to 1/4" hex.
Mike, you could use the part in my link above attached to a 1/4" hex socket...
-
-
Found one ;)
I don't think that will work. That is a 1/4" drive socket with 4mm hex. What Mike wants is a 4mm male bit on one end, and a 1/4" female hex on the other, to put 1/4" bits in. I've seen many the other way around to adapt 1/4" hex to 4mm, but not to adapt 4mm to 1/4" hex.
Mike, you could use the part in my link above attached to a 1/4" hex socket...
I'm not the expert here but I think its
1/4" hex Socket
4mm hex DriveBut maybe you are right, will do some more websearch.
Yup, INHEX, should be labeled INSquare, INTetra, INQuad its square, so you were right :-. -
You can make an adapter for the Philip's driver. Mine works for SAKs and Spirit alike.

-
@kkokkolis said:
You can make an adapter for the Philip's driver. Mine works for SAKs and Spirit alike.
wont work for the cybertools 29,34 and 41. they only have the bit driver ,not the philips.
-
@NutSAK - the linked one you posted could work and all I need is the socket! :)
@Etherealicer - Have to look at that closer! :)
@kkokkolis - I would know where to begin to make one and probably dont have the tools to do it with so looking to purchase one. It would be great to have one or two that work with many different models/MT's. Would it work using one of the flat heads, corner to corner? :D
Thx. for the replies everyone!
-
It works with the backscale driver but there's more play. And this driver isn't standard on cyber tools also.
-
A 4mm kit and a small magnet in the wrench is another option (up to Hex 4 at least). It will save weight, space and complexity.
-
Maybe I need to rethink my little kit setup and not use the CT34 in it and plan on a MT.
-
I think we're over thinking the bit driver as a bit driver- I always hate upsizing adaptors.
Try this http://forum.multitool.or...rum/91mm-sak-bit-adaptor/ and http://forum.multitool.or...arter-inch-drive-for-saks then tell us more about your kit. The more we know, the better we can help you spend your money. :D
[edit=fixed link]
-
Hmmm. Maybe what you need is a Minigrip - Or a modded one without the pliers.
If you find yourself needing a 1/4" bit driver often, maybe getting the Vic bit wrench or ratchet from a Swisstool is an alternative. Gives you a place to store the bits, too.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
