CRKT Tool
-
Yeah, I don't know where they get off making non plier based tools without pliers.... what were they thinking?

Def
-
Gave the wire stripper holes a go this afternoon and, while a little bit fiddly, did the job well enough.

-
I don't really like the "hole in the body then fold the knife blade" type strippers. I just roll the wire gently between my thumb and the blade until I cut all the way around.
I find all of these hold type strippers just too fiddly, not just this one.
Def
-
@Grant Lamontagne said:
I don't really like the "hole in the body then fold the knife blade" type strippers. I just roll the wire gently between my thumb and the blade until I cut all the way around.I find all of these hold type strippers just too fiddly, not just this one.
Def
TBH I agree. I've never had an issue stripping wire with just a blade either, but it's nice to know that this one works for those who do like them.
-
I know a few electricians and all of them use some sort of knife rather than any sort of commercially available strippers. While the few guys I know may not be much of a cross section for the entire electrical industry, I just don't see the point if them myself either.
Def
Sent from my MB860 using Tapatalk 2
-
Here is a quick update:
I have been carrying the CRKT Tool in my work vest for a few months now, in the rain, the cold, the ocean spray and in the sun. It's seen mud, dirt, hydraulic fluid and grease and I have not cleaned it, oiled it or maintained it in the least, preferring to torture test it. I've done on the spot repairs of my Jeep and a few other things, and I have to say that this tool has held up remarkably well.
There are no signs of rust on it at all. I'll take photos later on to prove it.
It hasn't been all rosy though- while both spring loaded screwdrivers still launch out, the lock on the flathead has become rather argumentative. It does not like to be released, meaning I have to use another tool to release the lock to fold the spring loaded driver, which is actually quite awkward. There is a good chance that a good cleaning and oiling would solve that problem though.
The other issue, and this isn't exactly a flaw in the tool, is that the pocket clip must have gotten hung up on something at some point and been stretched out a bit as it now catches on anything that comes near it. This is not a big deal though as it is held in by two screws, and so I'm sure I can pull it out, bend it back in shape and put it back on.
Functionally it hasn't been the best tool out there- I miss the pliers. The wrench sides are a nice feature but if the nut is too big (as many vehicle oriented nuts are) or if there's any overhang or limited access then it's very diminished. Of course, this is a failing of many of these types of wrenches, and again, not specific to this tool. Of course, pairing this with something like the CRKT Guppie or Spyder/ByrdRench to get the adjustable wrench would greatly enhance this one, and the only duplications would be the blades and since the screwdrivers would be different (similar heads but configuration/length is different). The blade duplication is ok too, as the CRKT Tool blade is more like a utility type knife, perfect for point work, while the Spyder/Byrd and Guppie have more fragile tips. The saw and bottle opener functions of the CRKT Tool would compliment the Spyder/Bird nicely since they are lacking those functions.
On to specific bits about the CRKT Tool itself- first up, I hate the name. Sorry CRKT folks who may be reading this, but the name is boring and awkward- sort of like Ford's new model, the Mercury Car. No smurf. We know what it is, why not give us a good handle to use? Hell, calling it the XL48.2 would even be better, despite it being a bit more pointless.
Functionally I like it. The blade seems pretty short when compared to the amount of available space, and normally that bugs the crap out of me, but I actually like it in this thing. It's short and stout so you feel like you can really use it and not worry about chips, scratches, dings or broken tips. If it were longer it would start to feel fragile or too elegant for manual labor- and no tool should be too elegant to be used.
The saw is also nice- it's not Wenger Ranger nice, but it has a decent length for any impromptu sawing needs. If you are cutting down trees in the yard, get a chainsaw. If you need to trim a few branches while camping or hiking it's quite good.
The wrenches, when they are in a situation where they work, they are great. I haven't slipped once with them, although as I said, there were a few situations where they weren't much use. Unlike one piece tools that are hollow the CRKT Tool has backsprings and other tools so if there's an extended bolt in there, it's not going to help you. Fixing that would lose you some other functionality though, and I'd rather have the saw, blade, screwdrivers etc.
The wire strippers have not seen any use- I never use those kinds of wire strippers. If anyone does, please feel free to let me know how these compare. For my own limited electrical work I'll continue on using the blade.
The T handle screwdrivers are nice- for T handled screwdrivers. They are great for applying torque to stuck screws, but kind of stink if those are long screws. Again, not a specific flaw with the XL48.2, but with T handled screwdrivers in general. Sadly the XL48.2 doesn't have any alternative- you can loosen the screw easily but then you are screwed if it's an inch or more long.
All in all I like the CRKT Tool despite the complaints above, and I'm not just saying that because the co-designer Tom Stokes is a friend. The thing is, a lot of manufacturers and designers make tools that are slick to use but really don't think of the odd time when a tool is going to be pushed hard. Sure there are warranties for the odd time that a really stuck screw has to be manhandled, but this tool gives up some convenience for it's ability to deal with things like stuck screws, drywall scoring and so on. Given it's skeletal type design it should be fairly easy to clean (when/if I ever clean mine I'll let you know how it goes :P) which means it's not only designed for hard jobs, it's also ready for the dirty ones. It's not perfect, but then no tool is. This one however is the kind of tool that is happy to get down and dirty and even better is at a price point where you might as well grab a couple of them so that you won't have to slow down when you send one in for warranty work in the off chance you do manage to push it too far.
But, make sure you carry a plier based tool too.
Def
-
Thanks for the feedback mate

Based on what you've said I'm going to stick with my initial assessment and say it would have been a lot better if they's "been inspired by" the driver on the X-Tract (flat and Phillips) on one side, leaving the other side free for scissors. That would resolve the driver lock thing (although when you clean it there might not be an issue anyway :D ) and reduce the clearance needed. It "might" also help clear up a bit of internal space (possibly with a little rejigging) to give the extra internal clearance for bolts to pass through the wrench area.
I totally agree on the name thing too ::) and overall I think it's a nice effort by the CRKT boys and it's good to see them trying out new concepts again, but I'm not convinced it's one for me.
I'm going to take another step towards lunacy :P and say I'd like it even better still (on top of my other suggestions ;) :D :D) if they either lost the wrench area altogether, or went for a removable one-piece-tool scale so the drivers and wrench could be used together :) That way the length of the blades and saw could be maximised.
-
I'm going to dust this thread off and record my experiences with this tool. Just got one. I've read all the past comments and was still curious. I picked the best of several I touched here at the crkt headquarters. About 3 miles from my home:) So I will still have my Charge TTi with me but it will be interesting to see later what tool I use first and for what. I will keep you all posted.
Sent from my KFSOWI using Tapatalk
-
I have to admit that I don't use mine an awful lot, but I do still think it's a quirky and fun concept. If I didn't use pliers a LOT at work I suspect I'd get a lot more use out of mine.
-
Had I (re)found this thread earlier, I might not have hit the buy me now button.
Now I am awaiting my CRKT tool to be delivered from the US.I´ll let you know how I like it.
-
I would not worry too much, as it is hard to be disappointed at the price. I really like mine so far. It's easy to get hung up on all the comments here. We all over analyze each tool. I have loved what others have hated, and vice versa. Sort of the circle of life here;)
Sent from my KFSOWI using Tapatalk
-
I know what you mean - I read about the downsides of my favourite tool, the MP 600, here quite regularly while I myself can´t get used to the LM Wave.
All good. Only thing that worries me right now is the delivery time. I wanna play! Errm..use my new tool. -
Play is what you shall do... especially with the switchblade drivers;)
Sent from my KFSOWI using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login