What did you use your Leatherman for today?
-
Very good story on your part, thank you for your warm welcoming! I will indeed check out your recommendations.
Sent from my iPhone using Tapatalk
-
I used the file on my BORebar and extended the handles to reach inside a trap to set the latch/trigger mechanism. We have a cat that has been living under our trailer for the winter it seems. One benefit is that we haven't noticed any mice or squirrels in quite a while, which would be something we'd see every so often.
-
@Monrogue said:
I used the file on my BORebar and extended the handles to reach inside a trap to set the latch/trigger mechanism. We have a cat that has been living under our trailer for the winter it seems. One benefit is that we haven't noticed any mice or squirrels in quite a while, which would be something we'd see every so often.That could be because is just so stinking cold there
I doubt you'd even see the cat around with those crazy temps 
-
Today, using my Surge, I fixed a reciprocating meat slicer at work. Dummies can't seem to understand the concept of tightening the bolts and screws on the spinning razor blade thingy.
The world belongs to the funkiest.
-
Sliced some knobs off an old worn tire with my Sidekick to make a makeshift commuter tire for my bike.
-
I used the file on my BORebar and extended the handles to reach inside a trap to set the latch/trigger mechanism. We have a cat that has been living under our trailer for the winter it seems. One benefit is that we haven't noticed any mice or squirrels in quite a while, which would be something we'd see every so often.
That could be because is just so stinking cold there
I doubt you'd even see the cat around with those crazy temps 
That's a good point too ;) Haven't caught the cat yet either...
-
Use the knife blade on my ST300 to cut some sections of sarking, which were then install on my shed roof.
(for the non-Aussies here, a quote from Wikipedia):
In current usage in Australia, sarking refers to a laminated aluminium foil layer (commonly described as RFL, or reflective foil laminate) that is installed on the roof trusses, beneath the battens, supporting a tile or metal deck roof. It acts as additional radiative and convective insulation and provides a condensation barrier.
Then in the afternoon, I repaired my friend who helped me with the sarking by helping him with some plumbing. ST300 saw and file both came in handy for cutting pipe, and removing the burrs afterwards
-
i took a piece of wood.
three bulb-lights,
three tea strainers
some ironwire
and a leatherman mut....

8) -
Used the PUG to re zero the sights on my air rifle this morning. Lot of help it was,shot line an idiot :ahhh
-
@screwloose said:
i took a piece of wood.
three bulb-lights,
three tea strainers
some ironwire
and a leatherman mut....

8)That's pretty neat

-
i took a piece of wood.
three bulb-lights,
three tea strainers
some ironwire
and a leatherman mut....

8)That's pretty neat

That is pretty neat, but did you use for the wings? JR
-
Used my Wave (old) to open some packaging. And the OHO blades are SO MUCH EASIER and MORE CONVENIENT than the Rebar.
Not to mention that I like and trust the Wave's liner locks better than the back locks on the Rebar.I'm not Rebar bashing, it's a great tool and I plan to give it motorbike carry duty. It's just not easy enough to access many times a day.
-
i took a piece of wood.
three bulb-lights,
three tea strainers
some ironwire
and a leatherman mut....

8)That's pretty neat

That is pretty neat, but did you use for the wings? JR
for the wings i used some kind of cloth with glue. That makes it hard like plastic. One tyrap as backbone and two on the flies body so you zip it in place.
-
-
Thanks JR :)
-
I used the scissors on my Sidekick-X to cut out some numbered label stickers for archiving boxes here at work

-
i had to chance the brakes on my motorbike.
there is a little pin to make the brakes capable to slide.
you need to remove that pin.
but how?....
my mut has a tool to dismantle a gun...
does that work on a BMW brake?
YEP!!
-
Used the serrated blade on mt LM Wave(REI Green handle) to cut up some hot Abruzzese dry sausage

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

