Little Boy and Fat Man
-
car, truck, garage, maybe somehow got buried in the snow? that little boy is worthy of an S&R operation
-
-
yep really good news. sadly I'm not close enough to lend a hand
-
Its gonna show.
-
It will. I'm sure of it...
-
At&t must have decided its worth more to them to leave my phone on.

-
How does that heater thing work? Gas out of the left bottle, water out of the right bottle?
Good news about the phone
hope things looks up a bit for you and your wife. -
@Cupboard said:
How does that heater thing work? Gas out of the left bottle, water out of the right bottle?Good news about the phone
hope things looks up a bit for you and your wife.You Nailed it.
That is how she works.
the left propane tank has a flame thrower hooked on to the hose end and the right tank holds water heated by the flame thrower. You fill the right tank with water by opening the top value close it. And then close the second value almost tight only open enough to let the right amount of steam out the end of the house.
-
Painting today.
I used the fat man to open cans , opening packages, cut tape , remove screws and nails, scraping a little paint off glass.
all easy jobs for the fat man
its a nice size tool to use but its almost to heavy to belt carry. Almost :)
-
I hope there's a pressure relief on there somewhere that I'm missing, it sounds bloody dangerous :ahhh
Rather ingenious though
-
According to a little bit of Googling, propane tanks (which is what I'm guessing you've got there) of about that size are rated to about 250psi assuming its in good condition. At 17 bar the boiling point of water is 200C.
Now it's been a few years since I did steam at uni and I wasn't really paying much attention then anyway, but that's a big bang with lots of very hot steam and shards of metal flying around.
In the case of water, a BLEVE could occur if a pressurized chamber of water is heated far beyond the standard 100 °C (212 °F). That container, because the boiling water pressurizes it, is capable of holding liquid water at very high temperatures.
If the pressurized vessel, containing liquid at high temperature (which may be room temperature, depending on the substance) ruptures, the pressure which prevents the liquid from boiling is lost. If the rupture is catastrophic, where the vessel is immediately incapable of holding any pressure at all, then there suddenly exists a large mass of liquid which is at very high temperature and very low pressure. This causes the entire volume of liquid to instantaneously boil, which in turn causes an extremely rapid expansion. That expansion is so rapid that it can be classified as an explosion, fully capable of inflicting severe damage on its surroundings.
Imagine, for example, a tank of pressurized liquid water held at 204.4 °C (400 °F). This vessel would normally be pressurized to 1.7 MPa (250 psi) above atmospheric ("gauge") pressure. Were the tank containing the water to split open, there would momentarily exist a volume of liquid water which is
at atmospheric pressure, and 204.4 °C (400 °F).At atmospheric pressure the boiling point of water is 100 °C (212 °F) - liquid water at atmospheric pressure cannot exist at temperatures higher than 100 °C (212 °F). It is obvious, then, that 204.4 °C (400 °F) liquid water at atmospheric pressure must immediately flash to gas causing an explosion.
Please put a pressure relief on or at the very least a pressure gauge. Please. A jet of steam that scalds you when it's getting too hot is much better than an explosion of steam.
I don't know what the laws over there are but in the UK by law all pressure vessels over a certain values (yours is, or could be) have to be inspected regularly to help ensure they're safe.
-
Ok Il make it safer Cupboard
like I said I didn't make it.
if I would have I would have included a safety pressure release.
-------------------)--)))----------))))----------))-))))---)))--//--////---\llllkk
todays' thoughts
I'm thinking I might drop the little boy from this review.
I don't know where else to look and buying / using a new one would not be fair .
if I just do it only on fat man I will try and use it for all my work and off work projects
I will carry whatever I feel like when I'm off work and grab the st300 as needed.
sorry I lost the little boy and in doing so wreaked my chance and a 2 for 1 topic /review. I didn't plan on what I should do if I lose a tool.
-
Well since I hear no objections.
I'm going to grab my spyderwrench.
if little boy shows up we will continue where we left off
Little boy
Born 7/13
M.I.A. 1/14we will never forget
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
:(