OPINELS
-
Was looking at the Opinel #8's again, thinking maybe a regular version over a flexible blade. Then saw one showing that there are only 5 pieces to the knife. Could not see how the blade hold into the handle & locking mechanisms, so it got me to wondering... can the metal parts come off the wooden handle end??
The photos were not very good for angles. It showed a pin, so am assuming the knife is only held into the handle via that pin only?
Still not sure if I want to get the bubinga wood. Seen walnut, beechwood, oak, and olive. Not sure which one would be more moisture resistant, or which would be the hardest of the woods offered.
The carbon blades seem to only come in beechwood, so may have to get their stainless steel version.
-
@Xelkos said:
Can the metal parts come off the wooden handle end??Yes, if you open the blade (pull hard) whilst the knife is locked shut the locking ring will pop out, so that it can be adjusted
The photos were not very good for angles. It showed a pin, so am assuming the knife is only held into the handle via that pin only?
Yes, but it is not a problem as it is large enough; most folding knives are just held by a pivot pin.
Still not sure if I want to get the bubinga wood. Seen walnut, beechwood, oak, and olive. Not sure which one would be more moisture resistant, or which would be the hardest of the woods offered.
There is a plastic version too. The wood, unless you keep it underwater for a long time is water resistant enough. You can also treat it.
The carbon blades seem to only come in beechwood, so may have to get their stainless steel version.
For general use the SS is better -no rusting
-
Here are a couple more of the mushrooms and some Stealth ;) porn...
I haven't been on much lately and trying to catch up. I can't believe I missed this one ??? Very nice D!¡! I'm so jealous

I will reply in a month.. :D
-
No.8 in Oak with SS blade
No.6 in Bubinga with SS blade
No.5 in Beech with carbon steel blade

The blade on the No.6 is polished like a mirror. It says on the box that the blade is Sandvik stainless steel.
-
That No.6 is lovely.

-
Flowered clover in an Aegean island and peasant's knife.

-
@kkokkolis said:
Flowered clover in an Aegean island and peasant's knife.
Is that a No. 8 Garden knife?
-
Oui!
-
Ultimate "opinel" ? :D
I saw this Chris Reeve Opinel copy/inspired/knockoff/similar/improvement ;) ... knife in BF and thought that it may be worthy of this thread. Damascus blade, though normal ones have also been made.
It uses a Helix lock which is, according to the internet, an improvement on the opinel lock. This was a very limited production knife for some reason.



Thread: http://www.bladeforums.com/forums/showthread.php/1146060-Found-one-of-my-grails-CRK-Helix
-
A very nice object of desire!
-
Very pretty! If it wasn't for the Damascus blade....
-
More than anything that knife makes me lose respect for Chris Reeves.
-
@Philthy said:
More than anything that knife makes me lose respect for Chris Reeves.Me too. I just don't like this knife. It might have better materials, but then a mysterious black thing in the lock? Damascus steel, but a thick blade and a strange point. (Is this a slight drop-point?)
And it does not even manage to be lockable when closed :P
Just is not my kind of fish, I like the Opinel x1000 better for a simple folder. -
K guys be gentle. I got a ss no8 to make a sheath for a friend. After using it for forming the two shown a lot of the leather dye had transfered to the handle. A quick rub down with sand paper sorted it, but then I got looking at the French sites. A quick rummage in one of the many box's of all things and I found some cocobolo wood from projects past. It is very satisfying whittling away in the knowledge that even if you smurf up something can be saved and hay it costs £8 to buy a new one. The little case I made to and holds my old no.4, and yes I did 'borrow' the design from the official Opinel one;-) .Sent from my Hudl HT7S3 using Tapatalk
-
Ok my latest effort. I have a couple to pieces of antler (benefits of a wife who works in a nature reserve.) A bit of cutting and shaping with a dermal, polish and here you are.
The stuff near the collar is leather covered in superglue, then polished. Not taking too much off the antler would have saved me this hassle.
Sent from my Hudl HT7S3 using Tapatalk


-
Yeh...good thing your not bringing that to London,you might not get to bring it back

-
Hmm... have some deer antler in storage. How difficult is it to make handles for the Opinels? Aren't the handles just one piece? Though antler would be tough, not to mention smelly, to work with.
-
Yes the handles are one piece. I cannot comment on the smell as I do not have a sense of smell, however it is the same as working bone and not the same as horn which I believe does smell.
Having cut the antler piece I wanted I next shaped the collar and using a sanding drum on a dremel. Go slow at this as you are also trying to keep everything straight. Use the collar to show where the channel for the knife to fit into goes. Again I used a dremal with a cut off disc to achieve this. The whole thing took about 2.5 hours.
Good luck.
Sent from my Hudl HT7S3 using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login