And so it begins.... (My adventures into Alox!)
-
Good video of an alox goodness.

-
@sticktodrum said:
Wow, that looks ridiculous. I'd love to grab one of those.

By the way, I finally uploaded a video I made about Bob's custom SAK I got a while back. I love this thing, and carry it most days. :D
It's a model you've all seen, but why not post it anyway?
Thanks for the great review!
I had planned more of a youtube presence to promote and sell my customs but the problem is I cant keep up to orders now, so I will wait until I can produce more before I start pumping out the youtube videos.
Cheers!

-
Back on the lock blade topic. Ana from Spain sent in some very well thought out notes on the lockblade issue and she had some good ideas.
Making the cuts wavy to eliminate stress points makes tons of sense. Hard to do by hand but if I waterjet cut a bunch that would work just fine.
Her first idea, I think is similar to what Chaka was suggesting. Im going to give that a try next as it sure look slike it should work.

-
I like those ideas.

The wavy pattern looks great.
-
Nice, I like the first or second, the wavy looks neat but I don't think it would have the lock effect like the others,, JR
-
I think this should work. If it is to replace the existing liner in a pioneer, I needed to have the cutout at the blade tip end. A normal pioneer blade is bent over so far that it would actually hit a full liner, but this way it should be enough to clear it.

-
@Syph007 said:
I think this should work. If it is to replace the existing liner in a pioneer, I needed to have the cutout at the blade tip end. A normal pioneer blade is bent over so far that it would actually hit a full liner, but this way it should be enough to clear it.Your option may be strong enough for the intended purpose. I just wanted to respectfully point out that the locking tab in your suggested solution would be under bending load with a relatively long lever arm. Alternatively, with a more conventional liner lock interface approach the loading would be mostly compressive. The likely result would be the ability to bear a greater closing torque before failing. In any event I look forward to seeing your prototype.
-
@Heywood Floyd said:
I think this should work. If it is to replace the existing liner in a pioneer, I needed to have the cutout at the blade tip end. A normal pioneer blade is bent over so far that it would actually hit a full liner, but this way it should be enough to clear it.
Your option may be strong enough for the intended purpose. I just wanted to respectfully point out that the locking tab in your suggested solution would be under bending load with a relatively long lever arm. Alternatively, with a more conventional liner lock interface approach the loading would be mostly compressive. The likely result would be the ability to bear a greater closing torque before failing. In any event I look forward to seeing your prototype.
Yep I came to that realization too. Next version will lock on 2 sides and that should work. Compressive force is the meat of the strength for sure.
-
Well I was stalled on the scalpel blade holder for ages and finally got back to it and solved it.
The problem was the scalpel holder itself wasnt quite big enough, and sat down too far inside. I figured I might as well just make a new pivot piece and then rivet the holder to that.
So.. I had a chunk of Ti scrap I milled some steps in.

And cut out a piece to use to form the pivot. I also milled a matching step into the blade holder.



I drilled 2, 1/16 holes and used brass rivets to attach the two pieces. Its very strong and solid.


I left some material on the top to be able to cut a nail nick.

And here is how it looks in the SAK.


-
Here are pics of the completed custom.








-
That's a very special one.
Glad you finally found a way to integrate it and I have a feeling this might become popular and requested tool in the future. -
Im thinking of adding a thin kydex sleeve over the blade. It feels a little dangerous opening it.

-
Yes, might be a good idea. But leave enough room around the edge not to dull it while sliding it off and on.
-
That's a sharp mod Syph... ::)
-
Unique setup Syph, love the serration! Nice job.. JR
-
I get asked ALOT in emails where my website is, do I have a site to show my work, etc etc. Well I finally got around to registering 2 domains. SAKModder.com and SAKMods.com
Now I need to figure out how to make a website. I did it years ago, but Im rusty.
-
That's a really cool mod Syph, and a website is a great idea
You need to show off that wonderful work to the masses. -
@Syph007 said:
I get asked ALOT in emails where my website is, do I have a site to show my work, etc etc. Well I finally got around to registering 2 domains. SAKModder.com and SAKMods.comNow I need to figure out how to make a website. I did it years ago, but Im rusty.
If you need any help, let me know. Would be glad to help out.
And sharp job on the scalpel.

-
I get asked ALOT in emails where my website is, do I have a site to show my work, etc etc. Well I finally got around to registering 2 domains. SAKModder.com and SAKMods.com
Now I need to figure out how to make a website. I did it years ago, but Im rusty.
If you need any help, let me know. Would be glad to help out.
And sharp job on the scalpel.

Very nice of you, wish I could help, but web-pages is not my area at all.
-
If you want help making video content for your site, I'm totally open to help. :D I already do product vids for KershawGuy.
That scalpel holder is really something, especially for use as an every day utility knife. Brilliant idea.
Sent from my Nexus 10 using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login