Squirt modification
-
I'm not sure if I over looked some other topic. But I'm looking for some help about the pins which hold a squirt together. I have tried to do a mod on a squirt and I took it apart by just drilling out the pins. But not really thought through that at one point everything should go back in and that I need something to hold it together
I've tought about rivets but I don't think that's going to work. Any suggestions? -
Check out this thread:Scibeer's SAK assembler.
Same principle applied to the Squirt may work for you. What mod are you going to do?
-
I work with boats and often have to cut some rope. And a serrated knife will do that job the best, I think. Usually I use the knife on my wave but I do not have it always with me. In that case I use the squirt. So I want a serrated knife in that one. And I want it to be locking as well. I already took it apart and I'm half way to put in a Spyderco ladybug knife in it. Those are rasor sharp and made of proper steel. I'll post some picture if my camera ever comes in from a shady online store (but that an other story), it will make things a bit more clear, I guess.
Anyway, I found some hollow brass tube that just fits nicely and screwed a tread (is that correct english?) in it so I can bolt it al together. But the result is bulky and not very tight. (The knife locking system will be my next problem) -
O yeah, I forget to mention. I've seen that thread. But can find a picture of the end result. Or am I just blind 8)
-
I didn't take any pictures of the finished knife for that thread since was just trying to show the jig. I'll try and find some shots of peening and post them.
You basically want to get a brass rod the same diameter as the pin you took out of the squirt and reassemble the knife, then leave about 2mm of brass on either side to peen over with a round tip hammer. Tap on the ends of the brass very lightly and slowly mold it into a head on each side. It takes me a hundred shots or more on each side for reference.
-
100+!? :o Must take you ages.
-
Thanks scibeer, but somehow it sounds more easy than it is :D Looking forward for a pic of the end result. In the mean time I'm on the hunt for some thin (1 or 1.5 mm) memory steel. (I'm not sure if that's the correct english translation for the steel I'm looking for) Because I do want some sort of liner lock for the knife. To much blood lost in the past with those non locking knifes!
-
I'm a fast tapper.
It goes pretty quickly. I counted 655 taps on a farmer the other day. I thought it woud be a much lower number.
It would probably be more useful to show pictures of the process with an alox knife since you won't be using rivets on your squirt. Brass or nickel silver rod is the way to go.
-
Wouldn't it be easier to get a small Spyderco full serrated knife? If you are wanting the squirt for the tools, why not pair the Spyderco with a LM Kick? ???
-
100+!? :o Must take you ages.
I'm a fast tapper.
It goes pretty quickly. I counted 655 taps on a farmer the other day. I thought it woud be a much lower number.
It would probably be more useful to show pictures of the process with an alox knife since you won't be using rivets on your squirt. Brass or nickel silver rod is the way to go.
655 taps :o. How long does it take you then to just build a Farmer ( just building not stripping the coating off etc)?
-
@Leatherman123 said:
Wouldn't it be easier to get a small Spyderco full serrated knife? If you are wanting the squirt for the tools, why not pair the Spyderco with a LM Kick? ???Because at work I alway have my trusty Wave on my belt. But there are some days that I just want a small tool in my pocket. And it seems that the Kick is not that much smaller as the wave.
My ideal tool, besides the wave, would be a squirt size tool (pliers) with a decent locking knife. That's not to much to ask, is it now? :D
So if any one has a good suggestion of a tool that fits that discription I would love to hear it. Otherwise I'm stuck with my own uncapable hands to build one. -
What if you got a SAK? Maybe like an OHT or something?
-
I've never really cared for the SAK's. But I have to admit I never really looked at them. On the other hand I never was a real MT guy either untill I needed some sort of tool for my work and encountered by accidant my current wave.
I think that was one of the best investment of my life (besides my girlfriend that is ;)) That's why I'm more of a MT guy than a SAK guy. Especially Leatherman, it just never lets me down!But I don't want to be narrow minded and open for everything. Do you have any SAK in particular in mind?
-
Hmmm, can't really think of anything that would fit the bill. Nothing that small at least.
The Wave is a great tool and if you're used to carrying it, you will miss the easy opening one hand blade and the strong pliers switching to a SAK IMO.
Vic still doesn't have the all in one package available in the multitool format. That said, I like the Spirit better than any other multitool even without the one hand opening blade.
Ben, Sounds like a lot of taps but each pin only takes about 1 minute to peen once you get the swing of things.
-
I never had a Spirit in my hands but it seems like a well made tool as well. But as you pointed out, I really need a one hand opening ( and closing) knife. On boats the first thing you learn is that one hand is for the boat and one for your self. You don't want to fall overboard :D
The pliers on a squirt are not that great either when you look at it but they seems surprisingly functional in my experience.It looks like I'm back at making something myself. The riveting earlier mentioned is not the way to go in my head, but if you have experience with that I like to hear it. It would make thing a lot more simple.
-
The knife pivot is at the pliers end of the Juice...I have my doubts about the shear strength of the brass pin stock that we use for SAKs for a Juice mod. A magnet tells me that the Juice pins are steel.
-
-
This is what I have so far. Don't laugh, it's my first attempt :D And I'm not exactly sure what I'm doing





-
Ahh, it makes sense now with pictures. That is quite a project. Do the screws not work properly as pivot pins?
-
No the screws does not have the right diameter. If I remember it correct the pin hole is 3.2 mm and as far as I know there are no screws with that diameter. At the moment I use hollow brass tube that fits exactly in the hole, tapped tread in it and used M2 screws to bold every thing together.
And to make things more easy :ahhh I had to find something to keep it together at the knife tip end that fits flush. So that the knife, which is a bit longer than the original knife, can be closed. If you know what I mean...
But I keep thinking back about the riveting option

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login