Show off your Sak mod's!
-
Been wanting to try this for a while. Reprofiled the gutting blade on a dual pro into a locking one hand electrician. Nice to have a smaller blade on a locking 111mm, so far I like it. :)
Wow, this is brilliant at least

Thanks! It's similar to a Weekender now only bigger, and locking. Now if it only had scissors and scale tools... :)
-
Been wanting to try this for a while. Reprofiled the gutting blade on a dual pro into a locking one hand electrician. Nice to have a smaller blade on a locking 111mm, so far I like it. :)
Wow, this is brilliant at least

Thanks! It's similar to a Weekender now only bigger, and locking. Now if it only had scissors and scale tools... :)
Nice! I like that one alot!
-
Right, here's the beginnings of the next knife:
Machining some aluminium plate down to 4mm thick. I've been ordering tooling and parts too - 2mm ball nose end mill, 3mm TiN coated stub drill, 3mm brass rod, stainless M2 CSK torx screws, a Compact and an Explorer. Can you guess what it's going to be? 8)
-
Alox Yeoman?
-
Been wanting to try this for a while. Reprofiled the gutting blade on a dual pro into a locking one hand electrician. Nice to have a smaller blade on a locking 111mm, so far I like it. :)
Wow, this is brilliant at least

Thanks! It's similar to a Weekender now only bigger, and locking. Now if it only had scissors and scale tools... :)
Nice! I like that one alot!
Thanks Syph! It's working great so far, slightly bigger (and heavier) than the OHT due to the additional locking liner, but still a nice carry size (in my pouch anyway). :)
-
-
-
Ball nose is for sure they way to go for an alox pattern.

-
Special SAK for a little girl.
This is still a work in progress, functionally it's pretty much there, but lots of finishing work still to be done. several grades of sandpaper to go and then polishing for the scales.
Pretty much everything sharp or pointy has been addressed.
Main blade replaced with a ruler
Small blade replaced with a nail file
Scissors given a round nose treatment
Can opener... may get its edge blunted, or even be ground back to a shape like a technician screwdriver. Jury still out on that one.
Awl replaced with a Wenger item, it's still there to make the backspring work, but the nail nick is inaccessible. But with a little work a cutout will make it usable again.
Corkscrew tip rounded off.
No T&T, small parts go in small mouths. Also I think it would spoil the look of the scales. (Artistic opinion, no correspondence will be entered into)
-
Nice one!
If you round out the Scissors, shouldn´t the Nailfile get the same treatment?
How old is the new owner? -
That ruler mods pretty cool! Idk about blunting the tips but that ruler is most definitely cool! JR
-
That's really cool and a great SAK for a child PTRSAK

-
Here's my just completed Brass Yeoman, ............the Bra-Man.
Solid brass scales, standard Yeoman tool load-out, but with the file on the Hook. Old Mag Glass and inline Phillips.Lanyard from 550 paracord, diamond knots.A toothpick lives under the hook, it's a cut-down plastic toothpick from the packets you get at a Pharmacy. The Cocoon was shrunk from electrical shrink-tubing, 22mm IIRC. Modern eyeglass screwdriver lives in the corkscrew.
The rivets were opened up to 2.5mm throughout, hand peened, all finishing on scales done with 400/600/1500 wet and dry, followed with Simichrome. Finish is not perfect, as you might expect with hand cut and finished scales, but it's quite presentable. Very solid heft with so much Brass, and great snap to the tools. Knife was assembled from parts, no Vic's were harmed during construction :) -
Bra Man!

That is Lush Neil - Nice one

-
Great work on the pins and polishing, Neill.

At first I thought the scales had a nail nick, and then realized that was a reflection from the ceiling. :D
Peter, love the scales and tool loadout.
I wouldn't worry about the can opener and would leave it as is. -
Yes, its just a reflection. No nail nick.
I may put a little relief into one scale though....I can get the combo tool out OK without it, but it does sit about 1mm too low.
The combo tool is originally from a 84mm knife. I enlarged the pivot to 2.5mm, and had to grind a smidge off the end of the spring, and increase the spring bend to get sufficient snap. Its just right now. -
-
@hiraethus said:
Ball nose cutter arrived.
Enough to do both scales.
Also tested the 3mm carbide cutter on an unwanted fish scaler - went through like butter. 8)
That's cool! JR
-
Nice checkering.

What size scales will you be making?
-
Thanks both. I'm making 91mm Plus scales for a Yeoman.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login







