Show off your Sak mod's!
-
Here's my just completed Brass Yeoman, ............the Bra-Man.
Solid brass scales, standard Yeoman tool load-out, but with the file on the Hook. Old Mag Glass and inline Phillips.Lanyard from 550 paracord, diamond knots.A toothpick lives under the hook, it's a cut-down plastic toothpick from the packets you get at a Pharmacy. The Cocoon was shrunk from electrical shrink-tubing, 22mm IIRC. Modern eyeglass screwdriver lives in the corkscrew.
The rivets were opened up to 2.5mm throughout, hand peened, all finishing on scales done with 400/600/1500 wet and dry, followed with Simichrome. Finish is not perfect, as you might expect with hand cut and finished scales, but it's quite presentable. Very solid heft with so much Brass, and great snap to the tools. Knife was assembled from parts, no Vic's were harmed during construction :) -
Bra Man!

That is Lush Neil - Nice one

-
Great work on the pins and polishing, Neill.

At first I thought the scales had a nail nick, and then realized that was a reflection from the ceiling. :D
Peter, love the scales and tool loadout.
I wouldn't worry about the can opener and would leave it as is. -
Yes, its just a reflection. No nail nick.
I may put a little relief into one scale though....I can get the combo tool out OK without it, but it does sit about 1mm too low.
The combo tool is originally from a 84mm knife. I enlarged the pivot to 2.5mm, and had to grind a smidge off the end of the spring, and increase the spring bend to get sufficient snap. Its just right now. -
-
@hiraethus said:
Ball nose cutter arrived.
Enough to do both scales.
Also tested the 3mm carbide cutter on an unwanted fish scaler - went through like butter. 8)
That's cool! JR
-
Nice checkering.

What size scales will you be making?
-
Thanks both. I'm making 91mm Plus scales for a Yeoman.
-
very neat :)
Sent from my HTC One X using Tapatalk
-
-
@hiraethus said:
Much, much filing later:


-
@hiraethus said:
Much, much filing later:

That's turning out pretty good! Keep it up! JR
-
First time playing with G10.
Black Vagabond with red shield and red G10 liner.

Sent from my HTC One X using Tapatalk
-
@hiraethus said:
Much, much filing later:


-
-
@Glofindel said:
First time playing with G10.
Black Vagabond with red shield and red G10 liner.

Sent from my HTC One X using Tapatalk
Very nice!

-
thank you^^
Sent from my HTC One X using Tapatalk
-
Bit more progress today. Drilled all the tools and back springs out to 3mm for the pivots with a carbide end mill. Drilled the scales to 3mm too, using the outer liners as templates. Now that they were lined up properly I was able to finish shaping and sanding the scales, and countersunk the screw holes:

They're a bit thick though, so I'll skim a millimetre off the back on the mill tomorrow.Tested the fit of all the parts (except the tools on the back) on the 3mm pins:

Couldn't resist putting the scales on to see what it looks like:

-
- Keep up the good work!
-
Turned the threaded pins, milled the scales thinner (it's no longer a Plus, more like a standard Alox) and managed to get the knife together tonight.
Took forever to assemble though - one of the holes in the scales is out of position and the screws are too long. I had to use a washer that was too thick between the knife blade and the scale so need to find some 0.2mm brass shim to make a thinner one. Finally, I need to find somewhere to hard anodise the scales for me.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login





