Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Mini driver question

Scheduled Pinned Locked Moved General Tool Discussion
25 Posts 1 Posters 3.0k Views
  1. Home
  2. Tool Talk
  3. General Tool Discussion
  4. Mini driver question
Mini driver question
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Faiaoga Offline
    Faiaoga
    Posts: 22
    Faiaoga Offline
    Faiaoga
    wrote on last edited by
    #20 Quote Reply

      I always have the Mini Screwdriver in the corkscrew of my Victorinox Spartan - just in case. Another useful gadget/gimmick/tool that I found recently is a set of four small bits in a small driver by Ace Hardware (only about $4). The bits are magnetic and include two Phillips (PH 0 and PH 000) ad two straight slot (1.5 mm and 30 mm). The set has a shirt pocket clip, measures about 3.5 inches long and 0.5 inches diameter and makes nice MacGyver tool to go along with a Swiss Army Knife and a multitool. Very light weight, so I always carry it next to my ball point pens and penlight. :nothingtoadd:

      1 Reply Last reply
      • Toolslinger Offline
        Toolslinger
        Posts: 2,453
        Toolslinger Offline
        Toolslinger
        wrote on last edited by
        #21 Quote Reply

          @Cupboard said:
          Since using thread locker on my glasses I haven't had any issues at all.

          +1. Same here.

          1 Reply Last reply
          • Cogito Offline
            Cogito
            Posts: 386
            Cogito Offline
            Cogito
            wrote on last edited by
            #22 Quote Reply

              @Faiaoga said:
              I always have the Mini Screwdriver in the corkscrew of my Victorinox Spartan - just in case. Another useful gadget/gimmick/tool that I found recently is a set of four small bits in a small driver by Ace Hardware (only about $4). The bits are magnetic and include two Phillips (PH 0 and PH 000) ad two straight slot (1.5 mm and 30 mm). The set has a shirt pocket clip, measures about 3.5 inches long and 0.5 inches diameter and makes nice MacGyver tool to go along with a Swiss Army Knife and a multitool. Very light weight, so I always carry it next to my ball point pens and penlight. :nothingtoadd:

              Do you have any pics or a link? I would like to see it if you don't mind :)

              1 Reply Last reply
              • av8r1 Offline
                av8r1
                Posts: 391
                av8r1 Offline
                av8r1
                wrote on last edited by
                #23 Quote Reply

                  I personally use the tip of the Style CS' nail file for my glasses. Works great; it's thinner than the one on the Micra so it works on smaller screws, and you're not trying to adjust a millimeter long screw with a pound of MT in your hand. I have used the one in the Wave successfully, but I don't tend to carry my Wave around with me.

                  1 Reply Last reply
                  • neillcurrie Offline
                    neillcurrie
                    Posts: 860
                    neillcurrie Offline
                    neillcurrie
                    wrote on last edited by
                    #24 Quote Reply

                      Wanting to see if it could be done, and also to see if it is practical, I took a standard Vic Corkscrew driver, removed the plastic with a dremel till I could see the anchored end of the steel shaft.
                      I then drove the steel shaft out of the plastic just far enough (maybe 1/4") to grind a Phillips flat bit on the end (about a 57 degree tip), and a small flat. I filled the small flat with JB Weld, also coated the shaft liberally, then drove the shaft back in to the plastic till the Phillips tip extended just a little. Let it all set up overnight, cleaned it up, and................

                      ..................it does work, but the shortness of the shaft overall means that either the flathead driver or the Phillips driver are a little too short to be used comfortably. The shaft length is a smidge short overall, and it can't be too much longer otherwise the steel shaft would mar the finish on the scales when the corkscrew closes.

                      photo.JPG

                      1 Reply Last reply

                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                      With your input, this post could be even better 💗

                      Register Login

                      1. Home
                      2. Tool Talk
                      3. General Tool Discussion
                      4. Mini driver question
                      Reply
                      • Reply as topic
                      Log in to reply
                      COMMUNITY LINKS
                      EDC-TV SAKWiki GearFeed SAKSelector
                      Operational Funds

                      Help us keep the Unworkable working!

                      Make A Donation
                      November Goal: $300.00
                      Due Date: Nov 30
                      Total Receipts: $0.00
                      Below Goal: $300.00
                      0% funded
                      • Login

                      • Don't have an account? Register

                      • Login or register to search.
                      • First post
                        Last post
                      0