Kampfer's EDC Gadgets
-
@Lam.Kampfer said:
Pocket Dump 030914Nice Carry Lam
One suggestion
I'd like to see you put a small fixed blade or mid to large size folder into your edc
I know you don't need one because the surge has nice oh opening blades.
Its nice to have something to cut the things you WANT and keep the surge ready for the things you HAVE to cut.I enjoy my knives. I don't need to carry one because I also always have a multitool tool on me.
I carry a endura most often. I keep it clean and razor sharp. Its almost insane what a razor sharp endura will cut through.
its fun cutting when you know its your edge melting through whatever its cutting through.
I take pride in my knives and what they can do.I think you may enjoy one also.
-
Noted, will consider.
Thanks, yes suggestion welcome! -
I know this is a very unusual approach, I just added a snap off utility knife to my setup.
It is OHO, light as air and stays razor sharp, good for general cutting tasks and fits on side of pouch very well.
I am going give it a few days to see how I like it.

-
If you like it you may also like the Gerber eab.
I've used the Smurf out if mine.
-
Have one, tried it, very good, but the forum factor doesn't work with my setup.
-
I carry a razor blade in my Wave nylon sheath and on my sheath I carry my Surge in. A razor for me is a known tool and can be very discrete when needed to be. I tend to carry them actually quite a lot and used to carry a box cutter but have delegated it to my Micro pouch.
-
I've been thinking about switching to a new surge for edc, but I'm thinking I might get more uses if I have a modded sidekick (replaceable bit driver, scissors, tweezers, and t-shank adapter) and a modded crunch (replaceable bit driver, awl and dental hook). What do you guys think?
-
In a long run, go with the New Surge as long as you found a way to carry the 12oz comfortably, it has everything you could ask for on a MultiTool.
All its wearable tools are replaceable, saw, file, wire cutter etc.
-
Here is the snap off knife I added, it was 5.25" long so I sawed it down to 4.25".
It weights less than the Swiss+Tech Utili-Key. -
I forgot to mention I used Surge's Bosch saw and file to shorten the knife.
Works well. -
Don't forget to add a metal saw for the t-shank adapter in case you need to do a jailbreak :)
-
@Cogito said:
I've been thinking about switching to a new surge for edc, but I'm thinking I might get more uses if I have a modded sidekick (replaceable bit driver, scissors, tweezers, and t-shank adapter) and a modded crunch (replaceable bit driver, awl and dental hook). What do you guys think?Did you know the Crunch already has a fullsize 1/4" hexbitdriver?
-
I've been thinking about switching to a new surge for edc, but I'm thinking I might get more uses if I have a modded sidekick (replaceable bit driver, scissors, tweezers, and t-shank adapter) and a modded crunch (replaceable bit driver, awl and dental hook). What do you guys think?
Did you know the Crunch already has a fullsize 1/4" hexbitdriver?
I did not know that :D Will it take LM bits?
-
Standard bit driver will take any LM bits, but LM bit driver won't take any standard bits.
-
good to know that makes it easier for me later :) Thx guys :D
-
I'm not entirely sure if it'll be ideal for the flat bits, it might be too deep for them. For hx bits, there's a notch to keep them from sinking into the driver, bit I don't know if that works for the flat ones.
-
Not ideal, but could work.
-
Pocket Dump

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login