What did you use your Leatherman for today?
-
Used the P.U.G to remount a scope on a Weirhauch HW25 for father and son at the gun club.
I'm not sure what the P.U.G is.
It's my Pretty Useful Guntool :D
-
I used the scissors on my Wave to cut out some addresses written on paper.
-
Used my Sidekick at work today to tighten a loose autoclave clamp.
-
@Monrogue said:
Earlier I was using my BORebar to aid me with prepping various documents to be fed to our large shredder here at work. I primarily used the pliers for pulling prong fasteners from folders, and gripping/tearing names from folders that were too thick to be put through the shredder. I had to use the serrated blade on a couple folders for the name removal task as they were tougher...but no match for the blade
More of this type of work today, but I used my new BO PST this time

-
Replaced telephone wire inside the trailer today, and relocated the inside jack. Employed the Charge TTi, Serac S2 (later the M5), Crunch, Piranha, and Squirt PS4.Used the cut hook to nick out some of the outer insulation on the wire, slipped in the guide, and stripped it down to the end. Worked rather slick. Use the saw to remove a small section of baseboard.
Had to use the Serac S2 to remove the problem jack that got corroded from a kitchen sink leak. Hot water inlet line burst and shot water all over the floor, which in turn soaked up in the carpet, which in turn nailed the cardboard boxes.
Messy to say the least, and smelly.Got 'er done though. Tried recycling the wall staples to hold the new wiring harness, that's where the Crunch was used. Most of the staples were less than cooperative and I finally threw in the white flag.

Went outside to finish the other end of the wiring when ran into a slight issue... the screwdriver ratchet was too long for the space I had.
Having no 1/4" ratchet was about to go get a wrench when I remembered the Piranha had a 1/4" hex driver. So... used the stubby adapter & socket to get that done.Of course when this idea popped into my head I ran inside to get the digital camera and Joby Gorillapod. Wanted to share the moment. :D
-
I just used the medium flat driver on my new BO PST to open the cover to the bathroom light as the bulb blew.
-
Used my Pulse to put a new light switch in my sons room. He somehow managed to break the old one.

-
Rebars serrated blade got a work out cutting zip ties.
-
Used the Phillips bit on my Charge to fix the latch on the gate on the side of my house. I also used it this morning to tighten the handle on a frying pan, and the can opener to open a can of corned beef hash for breakfast. :)
-
@jerseydevil said:
Used the Phillips bit on my Charge to fix the latch on the gate on the side of my house. I also used it this morning to tighten the handle on a frying pan, and the can opener to open a can of corned beef hash for breakfast. :)I take it that you like the Charge?
that's us mobile
-
PST got a workout today cutting zip ties and gaff tape. It's been a while since it's been out of the house.
-
@stealth007s said:
PST got a workout today cutting zip ties and gaff tape. It's been a while since it's been out of the house.Nice Terry
It's always good to hear of a PST getting some love ;) -
Used the Phillips bit on my Charge to fix the latch on the gate on the side of my house. I also used it this morning to tighten the handle on a frying pan, and the can opener to open a can of corned beef hash for breakfast. :)
I take it that you like the Charge?
Yep I am.
It's the first Leatherman to break into the rotation in quite a while...... -
Used the Phillips bit on my Charge to fix the latch on the gate on the side of my house. I also used it this morning to tighten the handle on a frying pan, and the can opener to open a can of corned beef hash for breakfast. :)
I take it that you like the Charge?
Yep I am.
It's the first Leatherman to break into the rotation in quite a while......Good, good. Slowly breaking yourself into Surge. Nice approach. ;D
that's us mobile
-
Speaking of SURGE, mine as always doing what it does best and thats WORK.
I'd take more pics but it would slow me down so one quick action shot.

-
Work in my colleges theater and use my super tool 300 daily from quick measurements.. Cutting tie line.. Those screws the screw gun can't reach..and the pliers for splinters.. Hanging lights.. And stripped screws.. So I tend to get my money's worth :)
Sent from my Galaxy Note 3
-
I cut some 12 AWG zip line to make a 6m dipole antenna with my Skeletool. I'm gonna be on the magic band pretty soon.
-
Used the Rebar to build a Nightstand and Dresser this morning.
-
Squirt S4 and Charge Ti (and MiniChamp, but that's in another thread :D ) for cutting gaff tape while working on a video production today.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
